Toon Brite Toon-Brite Protective Clear Coat For Boats

Toon-Brite Protective Clear Coat for Boats

Keep your boat looking its best with Toon-Brite Clear Coat: a tough, marine-grade finish made to protect metal and fiberglass surfaces. This non-conductive formula shields against oxidation, UV rays, salt spray, and electrolysis, making it ideal for aluminum, stainless steel, brass, copper, and more. It not only helps restore faded surfaces but also prevents future corrosion and staining. Easy to apply with a foam brush or HVLP sprayer after prepping the surface, this clear coat holds up for years in harsh marine conditions. Whether you're battling sun or salt, Toon-Brite adds a lasting layer of defense and shine.

Features:

Makes Future Cleaning Much Easier

Works On Aluminum, Fiberglass, Brass, Copper, Stainless and Most Metal Surfaces

Protects For Years Against Oxidations, UV Rays, Weathering, Stains, Salt Spray and Electrolysis

Restores and Rejuvenates Faded Or Oxidized Surfaces

Will Not Chip Or Peel

Corrosion Resistant

Great Color Restorer

Reduces Maintenance For Both Metal and Fiberglass

Non-Conductive

Sizes Available:

Gallon Coverage: 800-1200 Sq Ft.

12 oz. Spray Coverage: 120 Sq Ft

**Clear-coat is not an anti-fouling paint.

How to Apply Toon-Brite Protective Clear Coat

Toon-Brite Protective Clear Coat can be applied to aluminum, fiberglass, stainless steel, brass, copper, and galvanized steel. All surfaces must be clean, dry, and free of all contaminants (especially waxes, grease, & oils) prior to application.

Coverage: One quart will cover approx. 200-300 sq. ft.

Surface Preparation

Metal

Thoroughly clean surface with an acid wash.

Once the surface has been properly cleaned, test the surface for adhesion by applying Clear-Coat to a small area and observe for 5 minutes.

If the coating stays flat and flows out, the surface is adequately clean.

If beading occurs, re-clean.

Once surface is properly cleaned, apply 2 coats (or more) of Toon-Brite Clear Coat.

Fiberglass

Thoroughly clean the surface of oxidation, wax, and polish.

For heavy build up, use Toon-Brite Fiberglass Cleaner.

Apply Toon-Brite Clear Coat. Multiple coats may be necessary.

Follow up with fiberglass polish then wax.

Application Information

Provide adequate ventilation when applying Clear Coat and remove all sources of ignition or spark.

To apply by hand, use a 3" or 4" foam applicator.

To apply by spray, Toon-Brite recommends using a HVLP paint gun. If needed, dilute with acetone.

Apply to the surface in long even strokes being careful not to let runs or sags develop.

Make sure to overlap each pass.

The surface temperature should be above 50°F. Do not apply when humidity is above 85%.

For applications requiring multiple coats, the preceding coat should be dry to the touch.

Allow at least 8 - 24 hours to cure.

Clean up can be done with soap and water for hands. Use acetone or lacquer thinner for Clear-Coat clean up.

Toon-brite Protective Clear-Coat FAQ’s

• Q: What type of surface will Clear-Coat work on?

A: Clear-coat can be applied to Aluminum, Fiberglass, Copper, Brass, Stainless Steel, or any other surface you want to prevent from staining and discoloring.

• Q: Can you see Clear-Coat once it’s applied?

A: Clear-coat is virtually invisible on all surfaces other than a high polished surface. On a high polish finish, Clear-coat when wiped can sometimes leave slight sheen. This will some what lessen with a second coat and it also tends to diminish with time.

• Q: Will Clear-Coat work on painted surfaces?

A: Yes, Clear-coat can be applied to dull painted surfaces that are beginning to get chalky and oxidized. Clear-coat will prevent the chalky finish from returning as well as bring back a rich shiny finish.

• Q: What will Clear-Coat protect against?

A: Clear-coat will protect your surfaces from Oxidation, Stains, Weathering, Salt Spray, UV Rays, Corrosion and Electrolysis.

Q: How long wi…