Sea Hawk Sharkskin Bottom Paint

Sea Hawk Sharkskin Bottom Paint

The Sea Hawk Sharkskin is a traditional 45.2% copper-based hard-modified epoxy bottom paint. Made to aggressively combat all types of marine fouling including sea grass, green weed, barnacles, and other fouling organisms found in both salt and fresh water. Can be applied over most antifouling coatings.

Features:

Better color consistency for color matching

Highest grade cuprous oxide available

Most effective copper release rate

Consistent viscosity means better flow and rolling ability

Specifications:

Finish: Semi-gloss

Copper Content: 45.2%

VOC: 365 Grams/liter

Coverage: 320 sq. ft./gal.

Number of Coats: 2-3

Colors Available: 6145-Black, 6142-Blue

Pack Size: 1 US Gallon

How to Apply Sea Hawk Sharkskin Bottom Paint

Sea Hawk Sharkskin Bottom Paint is easily applied by brush, roller, or spray. When rolling, use only a high-quality short nap 3/8” roller cover. Apply using thin coats. For the smoothest possible finish, thin the paint approximately 10% using Sea Hawk 2053. Sharkskin has a tendency for settling to occur, especially if the paint has been on the shelf for several months. Thoroughly mix the paint before using. Before using, check the sides and bottom of the can to make sure all the pigment has been mixed in.

Finish: Semi-Gloss

Coverage: 320 Sq Ft

Application Method: Brush, Rolling, Airless Sprayer

Maximum Roller Thickness: 3/8” Nap

Number of Coats: 2

Wet Film Thickness: 5.0 mils

Dry Film Thickness: 3.1 mils

Application Temp: 50° F Min/ 95° F Max

Thinner: If necessary maximum 10% with Sea Hawk 2033

Drying Times

Substrate Temp

Touch Dry

Overcoating Time (Min)

Launch

73°F

2 hours

1 hour

12 hours

95°F

1 hour

1 hour

12 hours

Surface Preparation and Application

Previously Painted Surfaces

Known Compatibility of existing antifoulant

Power wash to remove any loose paint or other contaminants.

Scuff sand with 80 grit sandpaper, remove all residue and let dry.

Apply minimum 2 coats of Sharkskin. Allow 3-6 hours between coats and a minimum overnight dry.

Unknown Compatibility of existing antifoulant

Power wash to remove any loose paint or other contaminants.

Scuff sand with 80 grit sandpaper, remove all residue and let dry.

Apply 1 coat of 1277 Barrier coat primer or 1283 Island Primer

Apply minimum of two coats of SHARKSKIN. Allow 3-6 hours between coats and a minimum overnight dry.

Poor condition of existing antifoulant

If previous coating is cracking, peeling, or flaking strip the antifoulant with stripper, sanding, or commercial blasting.

Once stripped refer to the Bare Fiberglass Application Guidelines.

Bare Fiberglass

To prepare the surface it is important to remove all contaminants first. Scrub the surface with detergent soap and a stiff brush.

Using either S-80 Wax N’ Grease Killer or S-90 De-Wax Etch & Cleaner scrub the surface and rinse thoroughly.

Sand to a uniform dull looking surface with 80-100 grit sandpaper and rewash with S-80 Wax and Grease Killer or S-90 De-Watch Etch & Cleaner

Once cleaned and sanded, seal the surface with 2-3 coats of Tuff Stuff. Apply the second coat once the first has a tacky feel.

Apply minimum of two coats of Sharkskin. Allow 3-6 hours between coats and a minimum

Bare Fiberglass Sanding Method

Sand to a uniform dull looking surface with 80-100 grit sandpaper and rewash with S-80 Wax and Grease Killer or S-90 De-Watch Etch & Cleaner

Apply minimum of two coats of Sharskin. Allow 3-6 hours between coats and a minimum overnight dry.

Bare Fiberglass Non-Sanding Method:

Apply one thin coat of Sea Hawk 1266 no more than .3-.5 mils wet film thickness and allow to dry for 1 hour.

Apply minimum of two coats of Sharkskin. Allow 3-6 hours between coats and a minimum overnig…