Sea Hawk Monterey Bottom Paint

Sea Hawk Monterey Water-Based Bottom Paint

Sea Hawk's Monterey Antifouling Paint is a water-based, semi-hard ablative coating for vessels of all sizes and hull substrates. This premium bottom paint has been a leader in environmentally friendly antifouling protection for over a decade. Monterey paint is easy to apply, emits low VOC's, and contains the highest grade of cuprous oxide available. Its semi-hard ablative properties means it lasts longer and self-polishes to keep your hull smooth and barnacle-free. Monterey is also the perfect paint for boats stowed out of the water because its antifouling power is not reduced by removal from the water. Sea Hawk Monterey Bottom Paint can be applied over most existing bottom paint in good condition.

Features:

Consistent viscosity allows for a better flow and rolling ability

Low VOC's and highest grade of cuprous oxide available

Semi-Hard ablative finish to have lasting finishes on high speed vessels

Better color consistency for color matching

May be applied over most existing bottom paints

Proven to outperform other water-based paints

Easy cleanup with soap and water

Specifications:

Finish: Semi-gloss

Copper Content: 54.67%

VOC: 78 grams/liter

Coverage: 320 sq. ft./gal.

Number of Coats: 2-3

Colors Available: 5545-Black, 5430-Dark Blue

Pack Size: 1 US Gallon

How to Apply Sea Hawk Monterey Bottom Paint

Sea Hawk Monterey Bottom Paint is easily applied by brush, roller, or spray. When rolling, use only a high-quality short nap 3/8” roller cover. Apply using thin coats. For the smoothest possible finish, thin the paint approximately 10% using water. Monterey has a tendency for settling to occur, especially if the paint has been on the shelf for several months. Thoroughly mix the paint before using. Before using, check the sides and bottom of the can to make sure all the pigment has been mixed in.

Finish: Semi-Gloss

Coverage:  320 Sq Ft

Application Method: Brush, Rolling, Airless Sprayer

Maximum Roller Thickness: 3/8” Nap

Number of Coats: 2

Wet Film Thickness: 5.0 mils

Dry Film Thickness: 2.2 mils

Application Temp: 50° F Min/ 95° F Max

Thinner: Water

Drying Times

Substrate Temp.

Touch Dry

Overcoating Time (Min)

Overcoating Time (Max)

Launch

73°F

2 hours

1 hour

N/A

12 hours

95°F

1 hour

1 hour

N/A

12 hours

Surface Preparation and Application

Previously Painted Surfaces

Known Compatibility of existing antifoulant

Power wash to remove any loose paint or other contaminants.

Apply minimum 2 coats of Monterey. Allow 3-6 hours between coats and a minimum overnight dry.

Unknown Compatibility of existing antifoulant

Power wash to remove any loose paint or other contaminants.

Scuff sand with 80 grit sandpaper, remove all residue and let dry.

Apply 1 coat of 1277 Barrier coat primer or 1283 Island Primer

Apply minimum of two coats of Monterey. Allow 3-6 hours between coats and a minimum overnight dry.

Poor condition of existing antifoulant

If previous coating is cracking, peeling, or flaking strip the antifoulant with stripper, sanding, or commercial blasting.

Once stripped refer to the Bare Fiberglass Application Guidelines.

Bare Fiberglass

To prepare the surface it is important to remove all contaminants first. Scrub the surface with detergent soap and a stiff brush.

Using either S-80 Wax N’ Grease Killer or S-90 De-Wax Etch & Cleaner scrub the surface and rinse thoroughly.

Sand to a uniform dull looking surface with 80-100 grit sandpaper and rewash with S-80 Wax and Grease Killer or S-90 De-Watch Etch & Cleaner

Once cleaned and sanded, seal the surface with 2-3 coats of Tuff Stuff. Apply the second coat once the first has a tacky feel.

Apply minimum of two coats of Monterey. Allow 3-6 hours between co…