Sea Hawk Cukote Bottom Paint

Sea Hawk Cukote Bottom Paint

Sea Hawk's Cukote Bottom Paint is a self-polishing ablative paint that provides multi-season protection. Cukote Bottom Paint has a high load of cuprous oxide that makes this formula a top performer even in the most severe fouling areas. Due to its ablative and self-polishing nature, there is no buildup of bottom paint over time. The underwater surface of your hull remains clean and smooth, making this an ideal bottom paint for fast moving vessels. The copolymer in Cukote can withstand removal from water without affecting its antifouling properties. Sea Hawk's Cukote is the premium self-polishing antifouling paint that has established the standard in the industry.

Features:

Semi-Hard, self-polishing ablative finish

Multi-season performance

Removing boat from water does not affect antifouling properties

Effective below the waterline on fiberglass, steel, and wood vessels

No TBT (organotin compounds)

47.5% Cuprous oxide

Specifications:

Finish: Semi-Gloss

Copper Content: 47.57%

VOC: 398 grams/liter

Coverage: 346 sq. ft.

Number of Coats: 2

Colors Available: 3445-Black, 3441-Red, 3442-Blue, 3434-Teal

Pack Size: 1 US Gallon

How to Apply Sea Hawk Cukote Bottom Paint

Sea Hawk Cukote Bottom Paint is easily applied by brush, roller, or spray. When rolling, use only a high-quality short nap 3/8” roller cover. Apply using thin coats. For the smoothest possible finish, thin the paint approximately 10% using water. Cukote has a tendency for settling to occur, especially if the paint has been on the shelf for several months. Thoroughly mix the paint before using. Before using, check the sides and bottom of the can to make sure all the pigment has been mixed in.

Finish: Semi-Gloss

Coverage:  320 Sq Ft

Application Method: Bursh, Rolling, Airless Sprayer

Maximum Roller Thickness: 3/8” Nap

Number of Coats: 2

Wet Film Thickness: 5.0 mils

Dry Film Thickness: 2.2 mils

Application Temp: 50° F Min/ 95° F Max

Thinner: Maximum 10% Sea Hawk 2031 Reducer

Drying Times

Substrate Temp.

Touch Dry

Minimum Overcoat Time

Minimum Launch Time

73°F

2 hours

1 hour

12 hours

95°F

1 hour

1 hour

12 hours

Surface Preparation and Application

Previously Painted Surfaces

Known Compatibility of existing antifoulant

Power wash to remove any loose paint or other contaminants.

Scuff sand with 80 grit sandpaper, remove all residue and let dry.

Apply minimum 2 coats of Cukote. Allow 3-6 hours between coats and a minimum overnight dry.

Unknown Compatibility of existing antifoulant

Power wash to remove any loose paint or other contaminants.

Scuff sand with 80 grit sandpaper, remove all residue and let dry.

Apply 1 coat of 1277 Barrier coat primer or 1283 Island Primer

Apply minimum of two coats of Cukote. Allow 3-6 hours between coats and a minimum overnight dry.

Poor condition of existing antifoulant

If previous coating is cracking, peeling, or flaking strip the antifoulant with stripper, sanding, or commercial blasting.

Once stripped refer to the Bare Fiberglass Application Guidelines.

Bare Fiberglass

To prepare the surface it is important to remove all contaminants first. Scrub the surface with detergent soap and a stiff brush.

Using either S-80 Wax N’ Grease Killer or S-90 De-Wax Etch & Cleaner scrub the surface and rinse thoroughly.

Sand to a uniform dull looking surface with 80-100 grit sandpaper and rewash with S-80 Wax and Grease Killer or S-90 De-Watch Etch & Cleaner

Once cleaned and sanded, seal the surface with 2-3 coats of Tuff Stuff. Apply the second coat once the first has a tacky feel.

Apply minimum of two coats of Cukote. Allow 3-6 hours between coats and a minimum

Sanding Method:

Sand to a uniform dull looking surface with 80-100 grit sandpaper …