Pettit Paint Unepoxy HRT Bottom Paint

Pettit Unepoxy HRT Bottom Paint

Pettit Unepoxy HRT is formulated to provide outstanding protection at a very affordable price. Unepoxy HRT has a smooth durable finish that is able to withstand beaching, trailering, and season long abuse. This antifouling paint uses the latest technology available to create a hybrid paint film that's strong enough to handle the tough marine environment without building up over time.

HRT: Hybrid Reactive Technology features high density biocide utilization to maximize effectiveness, along with film modifiers to reduce yearly build-up, maintain color consistency, and lower weight.

Key Features:

Seasonal antifouling

Economical hybrid protection

Smooth durable polishing finish

Compatible over most bottom paints

Durable finish withstands beaching, trailering, and season long abuse

Colors Available: 1211 Blue, 1311 Green, 1611 Red, 1811 Black

• How Much Pettit Unepoxy HRT Do I Need for My Boat? Refer to the chart below to calculate how much Unepoxy HRT paint you will need for your boat.

Calculate the square footage of the hull to be painted - multiply the length of the hull by the beam then multiply that total by .85

Divide that number (your square foot total) by the amount of coverage Unepoxy HRT provides. (500 square foot per gallon). This will give you a one-coat total.

Example: If your boat has a length of 28', and a beam of 8.5', you will multiply 28 x 8.5 x .85 to get your total square footage. The total square footage for this boat is 202.3 square feet. A gallon of Unepoxy HRT has a coverage of 500 square feet per gallon for one coat, so one gallon will be enough for two coats.

How to Apply Pettit Unepoxy HRT

Unepoxy HRT is easily applied by brush, roller, or spray. When rolling, use only a high-quality short nap roller cover. Apply using thin coats. For the smoothest possible finish, thin the paint approximately 5-10% using 120 Brushing Thinner. Unepoxy HRT has a tendency for settling to occur, especially if the paint has been on the shelf for several months. Thoroughly mix the paint before using. Before using, check the sides and bottom of the can to make sure all the pigment has been mixed in.

Finish: Flat

Coverage: 500 ft2/gal

Application Method: Brush, roller, airless or conventional spray

Maximum Roller Thickness: 3/16"

Number of Coats: 1 minimum per season with additional coat at waterline

Wet Film Thickness: 3.75 mils

Dry Film Thickness: 1.5 mils

Application Temp: 50°F Min. / 90°F Max

Thinner: 120 Brushing Thinner

**Do not apply Unepoxy HRT on aluminum hulls or outdrives**

Previously Painted Surfaces

For old hard and ablative bottom paints, begin by thoroughly wiping down the surface with 120 Brushing Thinner. Pay extra attention to waterline areas. Then sand the painted surface with 80 grit sandpaper.

Old tin or copper copolymers, or Teflon-based antifouling paints should be sanded thoroughly with 80 grit sandpaper to remove the chalky outer surface. Wipe clean ten apply one coat of Unepoxy HRT.

Soft, sloughing antifouling paints should be removed before applying Unepoxy HRT.

Bare Fiberglass

All bare fiberglass, regardless of age, should be thoroughly cleaned with 92 Bio-Blue Hull Surface Prep or de-waxed several times with Pettit D-95 Dewaxer.

Non-Sanding Method (1): Prep the surface with 92 Bio-Blue Hull Surface Prep or wash the fiberglass three times using Pettit D95 Dewaxer. Then apply one thin coat of Pettit 6998 Skip- Sand Primer. Use a 3/16” or less nap when applying by roller. Consult the primer label for complete application and antifouling top coating instructions. Apply two or three thin coats of Unepoxy HRT.

Non-Sanding Method (2): Thoroughly clean, de-wax and etch the surface with 92 Bio-Blue Hull Surface Prep using a course Scotch-Brite pad in a swirling motion. Thoroughly rinse all residue from…