Pettit Paint EZ Bilge Quart

Pettit EZ Bilge Performance Bilge Paint

Pettit's EZ Bilge is a durable high-performance alkyd finish specially formulated to withstand the abuses associated with boat bilges. The hardwearing finish is resistant to antifreeze, grease, gasoline, diesel fuel, and engine oil. Its tough resilient surface will stand up to years of abrasion and wear. EZ-Bilge utilizes a high-solids formula that is easy to apply by brush, roller or spray and provides excellent coverage. Like other Pettit "EZ" products, EZ-Bilge provides the simplest way to achieve optimum results with minimum effort.

Features:

High-performance coating specially designed for boat bilges

Super tough finish is fuel, oil, and abrasion resistant

High covering formula is easy to apply

Superior protection that withstands tough bilge conditions

Specifications:

Type: Oil modified alkyd

Finish: High-gloss

Recommended Usage: Bilges

Colors Available: 3124 White, 3125 Gray

Coverage: 545 sq. ft/gal.

Number of Coats: 2 minimum

VOC: 388 grams/liter (max)

Associated Products

Pettit Brush Thinner -For brushing and clean up

Pettit Spray Thinner -Spraying Application

Pettit Bio-Blue - Surface cleaning for bare fiberglass and painted surfaces

How to Apply Pettit EZ Bilge Paint

Pettit EZ Bilge is a hard-wearing finish that can be applied to properly prepared fiberglass, metal, wood, and over existing metals. The surface must be free of dirt, loose paint, rust, oil, grease, wax, soap, and any other foreign matter. Stir thoroughly before use. EZ Bilge may be applied by brush, roller, conventional or airless spray. For brush or roller application apply without thinning although in hot weather 5 to 10% Pettit #120 Brushing Thinner may be added to maintain a wet edge. For best results on large, smooth surfaces roll out using a short nap roller followed immediately by leveling off with the tip of a brush. For conventional spray application thin 15 to 20% with Pettit 121 Spraying Thinner.

Application Methods: Brush, Roller, or Spray

Number of Coats: 2 minimum

Dry Film Thickness: 1.5 mils (3 wet mils)

Coverage: 545 sq. ft/gal.

Application Temp: 50°F Min. / 90°F Max.

Thinner: 120 Brushing Thinner or 121 Spraying Thinner

DRY TIMES:

Temp

To Touch

To Recoat

90°F

1-1/2 HR

8 HR

70°F

3 HR

16 HR

50°F

6 HR

24 HR

Application Systems

Painted Surfaces

Clean painted areas by washing with a solution of two cups household ammonia per gallon of water. Rinse well.

If the old paint is an oil-based enamel or polyurethane, and is in good condition, sand with 150 grit sand paper.

Solvent clean then apply first coat of EZ Bilge.

If the old oil-based or polyurethane paint contained a non-skid material, scrub the non-skid surface with Pettit 92 Bio-Blue using a stuff bristle brush.

Rinse thoroughly and allow surface to dry. Then apply two coats of EZ Bilge.

If the old paint is latex or water-based, or is in poor condition, remove it with a paint or varnish remover or by sanding.

Proceed with the instructions for the appropriate bare surface system.

Bare Wood

Sand surface smooth with 80-120 grit sandpaper.

Solvent clean with Pettit 120 Brushing Thinner.

Apply coat of 2018 EZ Wood Sealer.

Follow with one or two coats of 6149 EZ Prime until an evenly smooth base condition is reached.

Sand each coat with 80-120 grit sandpaper and solvent clean with Pettit 120 Brushing Thinner.

Proceed with the first coat of EZ Bilge.

Bare Steel

Surface must be cleaned to a bright finish.

Immediately apply one coat of 6980 Rustlok Primer. Allow to dry until tacky.

If surface is rough, apply a coat of 6627 Tie-Coat Primer. Sand well and solvent clean.

Repeat application of Tie-Coat Primer as needed until a smooth base is achieved.

Proceed with the first coat of EZ Bilge.

Bare Alum…