Interlux Paint Sikkens Cetol Marine Natural Teak Finish

Interlux Sikkens Cetol Marine Natural Teak Finish

Over time, all the potential environmental hazards, such as saltwater, wind, and scorching sun rays, can have their way with teak furniture and decking. Protect your investment with Sikkens Cetol Marine Natural Teak Finish. Cetol Marine’s Natural Teak formula actually enhances the natural wood grain, while its specially formulated UV- absorbing technology provides added protection with a durable, translucent, and protective wood finish. Sikkens Cetol marine natural teak is designed for use above the waterline on all interior and exterior woods. Sikkens Cetol Marine’s proprietary Next Wave technology features a unique UV-absorbing package, made from specialty resins and advanced UV absorbers. These special alkyd resin compounds and high-quality synthetic UV-absorbing pigments combine to create a “sunscreen” for enhanced color retention and wood protection.

• What is Next Wave technology? Next Wave technology is a UV-absorbing formula that acts as a sunscreen, ro protect wood by deflecting the damaging effects of the sun's UV rays. Next Wave will extend the longevity of the wood’s finish and enhance its color retention. The unique UV-absorbing finish in Sikkens Cetol Marine products protects the natural finish of wood and extends the beauty of the finish and the service life of your teak deck or deck furniture. Cetol Marine Natural Teak Finish can be used on exterior and interior hardwoods such as teak, mahogany, and oak. Sikkens Cetol Marine products should only be applied above the waterline. Specifications:

Finish: Satin

Number of Coats:2-3

Coverage:Approx. 360 ft²/gal

How To Apply Sikkens Cetol Marine Natural Teak Finish

Follow preparation procedures

One coat Cetol Natural Teak

Allow 24 hours for drying

One coat Cetol Natural Teak

Allow 24 hours for drying

One coat Cetol Natural Teak

Application: Use a long haired natural bristle brush. Apply in the direction of the grain.

Number of Coats: 3

Application Dos: Apply when temperature is between 50°F and 95°F. Saturate all end grains. Apply liberal coats and maintain a wet edge. For best results, apply in the direction of grain with a long haired natural bristle brush.

Don't apply In direct sunlight or when the surface is hot to touch. Do not apply in wet weather or when moisture content is greater than 18%. Do not apply Sikkens Cetol Natural Teak Finish below the waterline.

Surface Preparation:

New Exterior/Interior Wood:

Wipe the wood with Interlux Special Thinner 216 to remove any natural surface oils and contaminants. Once dry, sand the surface with 180-220 grit sandpaper, always sand along the length of the grain. Remove all sanding dust by vacuuming the surface.

Wipe the surface with Interlux Special Thinner 216 and allow it to dry before applying Sikkens Cetol Marine products.

Note: If the wood is exposed for more than 24 hours, clean the surface again with Interlux Special Thinner 216 in order to remove any surface contaminants

Exterior/Interior - Previously Coated Wood (Non-Cetol Marine Products):

Remove all existing coatings before applying Cetol. To remove old coating, either sand with 120-180 grit sandpaper or use Interlux Inter strip 299E chemical stripper specifically designed for marine use.

Once the previous coating is removed, follow instructions for New Exterior/Interior Wood.

Exterior – Weathered Wood or Previously Oiled Wood:

To ensure proper adhesion of Cetol products on weathered or previously oiled wood, use Interlux Premium Teak Restorer with a nylon scuffing pad as per instructions on label.

Be sure to rinse the wood well with clean water to remove surface dirt and allow it to dry thoroughly. This should be followed by the preparation procedures for New Exterior/Interior Wood.

Blue Fungi and Mildew:

Persistent blue fungi or…