Interlux Paint Pre-Kote Plus Boat Primer

Interlux Pre-Kote Plus Boat Primer

As one of the largest manufacturers of marine paints and primers, Interlux is a name you can trust for high-quality products that provide long-lasting protection for your boat finishes. The innovative technology has been leading the way for over a century in boat primers and paints, including the Interlux Pre-Kote Plus boat primer. Interlux’s commitment to research and development has helped to create a high-performance boat primer that has stood the test of time.

Pre-Kote Plus is a one part primer and undercoat that offers substrate protection with an ultra-smooth finish. Designed for use above the waterline Pre-Kote plus can be directly applied to most substrates including properly prepared metal. The lower VOC formula allows for easier application with improved flow. DIY customers will find Pre-Kote Plus to offer excellent flow, leveling, and easy to sand. Pre-Kote Plus is easy to use and the perfect foundation for your topcoat.

For an extra smooth  application should be done with a brush or roller, with a conventional sprayer being acceptable too. Interlux primer has a reduced working time with great substrate protection. It is recommended to apply 2-4 coats, depending on desired thickness. Make sure to correct surface imperfections before application. Sanding between each application is recommended for optimal application. Interlux Pre-Kote Plus is available in quarts and gallons. Each gallon covers ~440 sq/ft.

Specifications:

Finish: Matte

Application Method: Brush, roller or spray

Number of Coats: 2-4

Coverage: 440 sq. ft/gal per coat

Associated Products:

Thinner/Cleaner

2333N Reducing Solvent

333 Brushing Thinner

216 Special Thinner

Do not use this product on aluminum outdrives

How To Apply Pre-Kote Plus Primer

Interlux Pre-Kote is compatible with the following Interlux finishes: Bilgekote, Interdeck, Pre-Kote Plus, Toplac Plus, and Watertite.

Application Method:  Brush, Roller, Conventional Spray - Pressure Pot or Siphon Cup

Number of Coats: 2-4 As Needed

Dry Film Thickness per Coat: 1.9 mils (4 wet mils)

Coverage: 440 sq. ft/gal.

Application Temp: 41°F Min. / 95°F Max.

Thinning: Not usually required. Pre-Kote Plus can be thinned up to 10%. If thinned an additional coat may be required to achieve film thickness required to protect substrate

Brush: Solvent resistant standard brush

Roller: 4mm nap velour roller (If foam rollers are used a lower film build/opacity may be achieved and an additional coat required)

DRY TIMES:

Temp

Hard Dry

Touch Dry

Sandable

95°F

2.5 Hours

1 Hour

8 Hours

77°F

3 Hours

2 Hours

12 Hours

59°F

5 Hours

3 Hours

18 Hours

41°F

12 Hours

6 Hours

36 Hours

Note: Pre-Kote Plus must be sanded between coats.

Surface Preparation & Application

Previously Painted Surfaces

If in poor condition remove all previous coatings

Wash Down with a suitable detergent, rinse with fresh water and allow to dry

Sand with 220-280 grit paper

Remove all sanding residue

Wipe with 333 Brushing Thinner and allow to dry

Barewood

Sand with 80 - 180 grit paper

Remove sanding dust by brushing dusting and wiping

Wipe with 2333N Reducing Solvent

Plywood

Follow directions above for bare wood

Apply Inter-Prime Wood Sealer Clear 1026

Steel

Degrease with solvent or suitable detergent cleaner

Gritblast to Sa 2-1/2 - near white metal surface

If gritblasting is not possible, grind the metal surface with 24-36 grit abrasive discs

Grind to a uniform clean bright metals surface 50-75 micron anchor pattern

Use an angle grinder on small areas

Clean thoroughly and allow to dry completely

Aluminum

Degrease with solvent or suitable detergent cleaner

San well using 24 - 120 grit alum…