- All categories
Your cart
Product Comparison
How they are Different
|
__ __ |
|
|---|---|
| Description |
Description - __ |
| Vendor |
Vendor - __ |
| Color |
Color - __ |
|
|
Compare products ( / )
Fiberglass Evercoat
19 products
19 products
Sort by:
- Featured
- Most relevant
- Best selling
- Alphabetically, A-Z
- Alphabetically, Z-A
- Price, low to high
- Price, high to low
- Date, old to new
- Date, new to old
$89.49
Evercoat Sea-Glass 24oz Fiberglass Woven Roving
The Evercoat Sea-Glass Fiberglass Woven Roving is super-heavy, woven cloth for faster buildup and extra strength. Should be used in addition to mat and cloth to acquire the strength needed with minimal lay-up time. Use with polyester or epoxy resin in combination with glass mat where maximum strength and build-up are required.
Heavy weight, high strength
24 oz.
50" x 1 yd. (1.38 sq. yds.)
From $43.49
Evercoat Sea-Glass 1.5oz Fiberglass Mat Non-Woven
The Evercoat Sea-Glass Fiberglass Mat is best used for bulk "build up" when repairing holes and badly damaged areas. This mat is 100% fiberglass in a non-woven state; also molds and builds for repair of curved surfaces on fiberglass objects.
Best for high build-up repairs
Will conform to any shape
1.5 ounce weight
Sizes Available:
#940: 38" 34" (1 sq. yd.)
#941: 38" x 102" (3 sq. yds.)
$64.99
Evercoat Sea-Glass 6oz Fiberglass Tape
The Evercoat Sea-Glass Fiberglass Tape is perfect for fiberglassing seams, chines, keels, small patch jobs, corners, and edges. Sea-Glass Fiberglass Tape is also excellent for reinforcing seams and small repair areas. Cloth-woven tape in narrow width with a non-revealing edge. Use with polyester or epoxy resin.
6 oz
4" x 10 yds. (1.1 sq. yds.)
From $55.59
Evercoat Sea-Glass 6oz Fiberglass Cloth 44" Width
The Evercoat Sea-Glass Fiberglass Cloth is a high strength, flat weave cloth designed for covering large surfaces. This woven fiberglass material is suitable for all marine resins.
Has excellent drapability and wet-out.
6 oz weight
Sizes Available:
#911: 44" x 1 yd. (1.22 sq. yds.)
#912: 44" x 3 yds. (3.67 sq. yds.)
$115.69
Evercoat Gelcoat Repair Kit
Wear and tear on your gelcoat is inevitable, However, the Evercoat gel coat repair kit is a great choice for those nicks, gouges, and scratches to your fiberglass hulls or decks. This gelcoat repair kit permanently repairs imperfections and the material cures within an hour to a durable glass-hard finish. This gelcoat repair kit is quick and easy to apply and comes with a special release film and no-run polyester gel that dries slick for a no-sand finish.
This gelcoat repair kit comes with everything you need for repairs to your gelcoat including polyester gelcoat paste, hardener, release film mixing stick, and a blending chart with instructions. For a perfect match, blend this gel coat repair kit directly on your hull or deck. This repair kit can also be used for appliances, countertops, tubs, and sinks.
Complete kit contains:
Polyester gel coat paste 1 fl. oz.
6 Color Agents .25 fl. oz. each
Liquid Hardener .25 fl. oz.
Special release film
(2) Mixing sticks
Sandpaper 4.5" x 5.5"
Instruction sheet with color matching guide
***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***
Frequently Asked Questions
- What is the Evercoat Gelcoat Repair Kit used for? The Evercoat Gelcoat Repair Kit is designed to repair nicks, gouges, scratches, and other imperfections in fiberglass hulls and decks. The kit uses a no-run polyester gelcoat that cures to a durable finish and includes materials for blending the repair color directly on the surface.
- What does the Evercoat Gelcoat Repair Kit include? The kit includes 1 fl. oz. of polyester gelcoat paste, six 0.25 fl. oz. color agents, 0.25 fl. oz. of liquid hardener, special release film, two mixing sticks, a 4.5 x 5.5-inch sheet of sandpaper, and an instruction sheet with a color-matching guide.
- How does the Evercoat Gelcoat Repair Kit achieve a color match? The included color agents can be blended directly on the hull or deck to match the existing gelcoat. A color-matching guide is included with the kit to assist with the blending process and help create a closer match to the repaired surface.
- Does the Evercoat Gelcoat Repair Kit require sanding after application? The kit includes a special release film and no-run polyester gelcoat that dries slick for a no-sand finish. Sandpaper is also included in the kit, along with the other materials needed for gelcoat repair.
- How quickly does the Evercoat Gelcoat Repair Kit cure? The polyester gelcoat material cures within approximately one hour to a durable, glass-hard finish. The product is designed as a quick and easy repair solution for imperfections in gelcoat surfaces.
- Can the Evercoat Gelcoat Repair Kit be used on surfaces other than boats? Yes. In addition to fiberglass hull and deck repairs, the Evercoat Gelcoat Repair Kit can also be used to repair imperfections on appliances, countertops, tubs, and sinks.
$79.09
Polyester Gel Paste Pint
Neutral color polyester paste for permanent gelcoat marine repairs. Neatly covers gouges, scrapes and scratches in fiberglass. Coloring agents provide correct color match. Hardener included. 1 Pint ***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***
SDS
Frequently Asked Questions
- What is Polyester Gel Paste Pint used for? Polyester Gel Paste Pint is a neutral-color polyester paste designed for permanent gelcoat repairs on marine fiberglass surfaces. It can be used to cover gouges, scrapes, and scratches, providing a repair material that can be colored to match the surrounding gelcoat.
- Can Polyester Gel Paste be color matched? Yes. Coloring agents can be used with the neutral-color polyester gel paste to achieve the correct color match for the fiberglass surface being repaired. This allows the repair material to be adjusted to better match the existing gelcoat.
- Does Polyester Gel Paste Pint include hardener? Yes. The Polyester Gel Paste Pint includes hardener, so the product contains the hardening component needed for the gelcoat repair application.
- What types of fiberglass damage can Polyester Gel Paste repair? Polyester Gel Paste is designed to cover common fiberglass gelcoat imperfections, including gouges, scrapes, and scratches. It is intended for permanent marine gelcoat repairs where the damaged area needs to be filled and restored.
- What size is the Polyester Gel Paste? Polyester Gel Paste is supplied in a 1-pint container. The paste is neutral in color and can be combined with coloring agents to achieve the desired color match for the repair.
$131.99
Evercoat Gelcoat Match & Patch Repair Kit
The Evercoat Gelcoat Match & Patch Repair Kit permanently repairs nicks, gouges and scratches in fiberglass hulls and decks. Blend coloring agents to achieve a match to almost any color. Repair material cures glass-hard in one hour. A special release film and no-run polyester gel makes a slick , no-sand finish quick and easy. Mix colors directly against hull or deck for a perfect match. Also can be used to repair counter tops, appliances, bathroom tubs and sinks.
This Kit comes with an instruction sheet with color match guide.
Kit Includes:
Polyester gelcoat repair paste - 4 fl. oz.
Liquid hardener - .25 fl. oz.
6 color pigments - .25 fl. oz. each
Cleaning solvent - .75 fl. oz.
Mixing Cups
Spreader
Stir Sticks
Special release film
***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***
$112.69
Evercoat Fiberglass Repair Kit 8oz
The Evercoat Fiberglass Repair Kit delivers fast and easy permanent repairs of fiberglass, most woods, and metals. Kit strengthens, repairs, and rebuilds. Repair cracks and holes in fiberglass and wood. May be used for small lay-up jobs or fabricating missing fiberglass panels.
Kit Includes:
8 fl. oz. resin
1/4 oz. liquid hardener
3 sq. ft. fiberglass cloth
Mixing stick
Plastic spreader
Mixing tray
Instructions
***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***
From $11.49
Resins & Gelcoat Liquid Hardener (MEK)
Hardening agent for use with all polyester resins and gel coats. Plastic squeeze tube has graduated measure for mixing convenience. Use this Methyl Ethyl Ketone Peroxide catalyst according to the resin/gel coat label directions.
***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***
SDS
$37.99
Fiberglass Evercoat Acetone
Evercoat Acetone is a powerful, fast evaporating, water miscible chemical. It can be used as a clean-up solvent for epoxies, vinyl, lacquers, contact cements, plastics, and adhesives. Acetone may also be used as a fiberglass cleaner to assure adhesion of resin. It is also an effective solvent for polyester resins used in boat and auto body repair kits.
Features:
Size: Quart
Fast evaporating
Clean-up solvent for epoxies, vinyl, lacquers, contact cements, plastics, and adhesives.
Click to Download Evercoat Acetone SDS
Frequently Asked Questions
- What is Fiberglass Evercoat Acetone used for? Fiberglass Evercoat Acetone is a fast-evaporating, water-miscible solvent used for cleanup of epoxies, vinyl, lacquers, contact cements, plastics, and adhesives. It can also be used as a fiberglass cleaner to help assure resin adhesion and as a solvent for polyester resins used in boat and auto body repair kits.
- Can Fiberglass Evercoat Acetone be used for fiberglass repair? Yes. Fiberglass Evercoat Acetone may be used as a fiberglass cleaner to help assure adhesion of resin. It is also an effective solvent for polyester resins used in boat and auto body repair kits.
- What materials can Fiberglass Evercoat Acetone clean up? Fiberglass Evercoat Acetone can be used as a cleanup solvent for epoxies, vinyl, lacquers, contact cements, plastics, and adhesives.
- Is Fiberglass Evercoat Acetone fast evaporating? Yes. Fast evaporation is a listed feature of Fiberglass Evercoat Acetone, making it a solvent option for the cleanup applications specified by the product description.
- How much Fiberglass Evercoat Acetone is included? Fiberglass Evercoat Acetone is supplied in a quart-size container.
From $36.49
Formula 27 Polyester "Miracle Mender" Filler
Permanent repair of fiberglass, wood, metal, stucco and drywall. High quality, white plastic filler for filling dents, scrapes and gouges. This product does not shrink after curing. A true "miracle mender" that won't crack or pop out. A long time favorite of consumers everywhere. Formula 27 can be tinted with Evercoat Coloring Agents. White cream hardener is included. ***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***
SDS
Frequently Asked Questions
- What is Formula 27 Polyester "Miracle Mender" Filler used for? Formula 27 Polyester "Miracle Mender" Filler is a white plastic filler designed for permanent repairs to fiberglass, wood, metal, stucco, and drywall. It can be used to fill dents, scrapes, and gouges.
- Does Formula 27 Polyester "Miracle Mender" Filler shrink after curing? No. Formula 27 is formulated not to shrink after curing. The product description also states that it is designed to resist cracking or popping out after repair.
- What surfaces can Formula 27 filler be used on? Formula 27 Polyester "Miracle Mender" Filler is designed for repairs on fiberglass, wood, metal, stucco, and drywall. It can be used to fill dents, scrapes, and gouges in these materials.
- Can Formula 27 Polyester "Miracle Mender" Filler be tinted? Yes. Formula 27 can be tinted using Evercoat Coloring Agents. The filler is supplied as a white plastic filler.
- Does Formula 27 Polyester "Miracle Mender" Filler include hardener? Yes. A white cream hardener is included with Formula 27 Polyester "Miracle Mender" Filler.
$32.29
Evercoat PVA Mold Release 8 oz.
Evercoat PVA Mold Release is a water-soluble liquid mold release that forms a smooth parting film, allowing a glossy finish on molded surfaces. This product promotes complete cure of Polyester Gel Coat.
How to Apply Evercoat PVA Mold Release
Mold Release is best applied by spraying, however, this product can also be applied with a soft bristle brush. 8 fl. oz. should cover approximately 20 sq. ft.
Apply with a small orifice spray gun using 90-100 psi or an aerosol spray.
Spray at a distance of 12-18".
Apply a mist coat followed by a heavier full wet coat.
If applying by brush, apply one full coat and allow to dry approx. 30-60 minutes before applying resin to mold.
Gel Coat Application
When used to promote the complete cure of Gel-Coat, do the following:
Apply one full wet coat by spray or brush to the uncured gel coat surface.
Allow gel coat to cure for 4-6 hours before removing mold release.
PVA Mold Release can be removed from mold or gel coat with water.
Click to Download Evercoat PVA Mold Release SDS
Frequently Asked Questions
- What is Evercoat PVA Mold Release 8 oz. used for? Evercoat PVA Mold Release is a water-soluble liquid mold release that creates a smooth parting film on molded surfaces. It helps provide a glossy finish and can also be used to promote complete curing of Polyester Gel Coat.
- How do you apply Evercoat PVA Mold Release? Evercoat PVA Mold Release is best applied with a small-orifice spray gun using 90-100 psi or an aerosol spray, from 12-18 inches away. Apply a mist coat followed by a heavier full wet coat. It can also be applied with a soft bristle brush.
- How much area does the 8 oz. size of Evercoat PVA Mold Release cover? The 8 fl. oz. size of Evercoat PVA Mold Release should cover approximately 20 square feet. Actual coverage can depend on how the product is applied and the amount used to form the mold release film.
- How is Evercoat PVA Mold Release used with Polyester Gel Coat? To promote complete curing of Gel Coat, apply one full wet coat of Evercoat PVA Mold Release to the uncured gel coat surface by spray or brush. Allow the gel coat to cure for 4-6 hours before removing the mold release.
- How do you remove Evercoat PVA Mold Release? Evercoat PVA Mold Release is water-soluble and can be removed from the mold or gel coat with water. When applying it by brush, allow the coat to dry approximately 30-60 minutes before applying resin to the mold.
$126.99
Evercoat Gel-Kote Neutral - Quart
Evercoat's Gel-Kote manufacturers the highest-quality, ISO NPG marine finish gel coat used to permanently repair or replace an original, high-gloss finish. Evercoat Gel Kote cures to a hard finish andEvercoat Mold Release (# F-E-5685) must be used to attain a fully cured surface. It is great for filling gouges, chips, scrapes, and deep scratches in the fiberglass gel coat on your vessel. One Step Finish Gel-Kote is a non-run, non-sag formulation of flexible polyester resins designed for durability and toughness. Evercoat Coloring Agents can be used to tint the gel coat to your desired color. Use in conjunction with Evercoat Acetone (10%) for easy sprayer applications.
Quart Size
Fills chips, gouges, scrapes and scratches
Cures to hard finish
One-step finish
Can be tinted with Evercoat coloring agents
Neutral color
WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY
From $82.99
Premium Gel-Kote White
The quality ISO NPG marine laminating gel coat to permanently repair or replace original, high-gloss finish. The product cures to a tacky finish for re-coating. Evercoat Mold Release (#F-E-5685) must be used to attain a fully cured surface. Use to fill gouges, chips, scrapes and deep scratches in the fiberglass gel coat. Gel Kote is a non-run, non-sag formulation of flexible polyester resins to produce resiliency and toughness. Evercoat Coloring Agents may be used to tint the material to desired color. Reduce with Evercoat Acetone (10%) to thin for sprayer applications.
***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***
Frequently Asked Questions
- What is Premium Gel-Kote White used for? Premium Gel-Kote White is an ISO NPG marine laminating gel coat designed to repair or replace the original high-gloss finish on fiberglass. It can be used to fill gouges, chips, scrapes, and deep scratches in fiberglass gel coat and cures to a tacky finish for recoating.
- How does Premium Gel-Kote White cure? Premium Gel-Kote White cures to a tacky surface that is intended for recoating. Evercoat Mold Release must be used when a fully cured surface is required. Follow the product directions for the appropriate finishing process.
- Can Premium Gel-Kote White be used to repair fiberglass gel coat damage? Yes. Premium Gel-Kote White is formulated for permanent repair or replacement of fiberglass gel coat and can fill gouges, chips, scrapes, and deep scratches. Its non-run, non-sag formulation uses flexible polyester resins to provide resiliency and toughness.
- Can Premium Gel-Kote White be tinted to match a fiberglass surface? Yes. Evercoat Coloring Agents may be added to Premium Gel-Kote White to tint the material to the desired color. This can help when matching the gel coat to an existing fiberglass surface.
- Can Premium Gel-Kote White be sprayed? Yes. Premium Gel-Kote White can be reduced with Evercoat Acetone at 10% for sprayer applications. The product is otherwise formulated as a non-run, non-sag gel coat for fiberglass repair and finish restoration.
From $100.69
Evercoat Gel-Kote One Step Finish Gel Coat Repair - White
This is the highest quality ISO NPG One Step Finish Gel Coat that permanently repairs or replaces your vessels’ original, high-gloss finish. The gel coat will cure to a hard finish and will not require Evercoat Mold Release (# 105685) in order to attain a fully cured surface. It can be used to fill gouges, paint chips, finish scrapes, and deep scratches in your fiberglass gel coat. One Step Finish Gel Coat will not run or sag and its formulation of flexible polyester resins produce amazing resiliency and toughness. So versatile, Evercoat Coloring Agents can be used to tint the material to your desired color. Reduce the one step finish gel coat with Evercoat Acetone (10%) in order to thin for sprayer applications.
Superior finish
Resilient, one-step Isophthalic Polyester Gel Coat
Non-run, non-sag formulation
Sizes Available:
Pint
Quart
CAN ONLY SHIP WITHIN THE CONTINENTAL U.S.
How to Use Evercoat One Step Finish Gel-Kote
Remove all paint, grease, oil, dirt or wax. Sand only affected area with coarse grit abrasive.
Wipe area clean with Evercoat Acetone.
If tinting the Gel-Kote, mix in the color prior to catalyzing the Gel Coat. Use Evercoat Color Agents (maximum 1 oz. color agent per quart of Gel-Kote).
Add the hardener to the Gel-Kote in the following proportion: 12 drops hardener to 1 ounce of Gel-Kote.
Note: the mixed product will start to gel in approximately 15 minutes. Temperatures hotter than 90°F will shorten the gel time and temperatures below 70°F will lengthen it.
Mix well for 2 to 3 minutes and apply to the repair area. Gel-Kote can be reduced for spraying by adding 10 to 15 percent of Evercoat Acetone.
Apply catalyzed Gel-Kote to a thickness of approximately 20 mils.
The formula will completely cure to a hard surface in approximately two hours.
Clean all tools with Evercoat Acetone before the product hardens.
Frequently Asked Questions
- What is Evercoat Gel-Kote One Step Finish Gel Coat used for? Evercoat Gel-Kote One Step Finish Gel Coat is designed to repair or replace the original high-gloss finish on fiberglass vessels. It can be used to fill gouges, paint chips, scrapes, and deep scratches in fiberglass gel coat. The non-run, non-sag formula cures to a hard finish without requiring Evercoat Mold Release.
- How do you apply Evercoat Gel-Kote One Step Finish Gel Coat? Remove paint, grease, oil, dirt, and wax, then sand the affected area with a coarse-grit abrasive and clean it with Evercoat Acetone. Add the specified amount of hardener, mix thoroughly for 2-3 minutes, and apply the catalyzed Gel-Kote to approximately 20 mils thickness.
- What is the mixing ratio for Evercoat One Step Finish Gel-Kote? Add 12 drops of hardener to each 1 ounce of Evercoat Gel-Kote. Mix the components thoroughly for 2-3 minutes before application. The mixed product begins to gel in approximately 15 minutes. Temperatures above 90°F shorten the gel time, while temperatures below 70°F lengthen it.
- Can Evercoat Gel-Kote One Step Finish Gel Coat be tinted or sprayed? Yes. Evercoat Color Agents can be mixed into the Gel-Kote before adding the hardener, using no more than 1 ounce of color agent per quart of Gel-Kote. For spray application, the product can be reduced with 10-15% Evercoat Acetone. Follow the specified mixing and catalyzing procedure before applying.
- How long does Evercoat One Step Finish Gel-Kote take to cure? After application, Evercoat Gel-Kote One Step Finish Gel Coat completely cures to a hard surface in approximately two hours. The mixed product begins to gel in about 15 minutes, although actual gel time varies with temperature. Clean application tools with Evercoat Acetone before the product hardens.
- What sizes are available for Evercoat Gel-Kote One Step Finish Gel Coat? Evercoat Gel-Kote One Step Finish Gel Coat is available in pint and quart sizes. The product is described as an…
From $34.69
Evercoat Marine Gel Coat Scratch Patch
Use Evercoat Gel Coat Scratch & Patch to repair fiberglass boats, bathtubs, shower stalls and hot tubs. This product provides easy permanent repairs on hairline cracks, small scratches and chips in fiberglass. This one part formula does not need a catalyst. Just fill in the crack, let is set and scrape off the excess with the enclosed spreader. It is just that easy. Clear Scratch Patch is ideal for surface scratch repairs of metal flake finish. Available in 1/2 fl. oz. ounce bottle.
Features:
Includes spreader for removing excess
Fast, easy-to-use fiberglass gel coat repair
Also repairs paint, linoleum, Formica, and some plastics
1/2 fl. oz.
How to Use Evercoat Gel Coat Scratch Patch
Apply Evercoat Gel Coat Scratch Patch at temperatures 60°F or above.
Clean surface and allow to completely dry.
Apply enough product to fill scratch or chip, allowing a small excess to build up above & around area.
Allow to dry for 15 minutes.
Remove excess with plastic scraper (included).
Allow area to dry for an additional 30 minutes.
Finish area with a marine wax.
Avoid washing or scrubbing the area for 3 days.
Note: Color tends to darken after drying.
Frequently Asked Questions
- What is Evercoat Marine Gel Coat Scratch Patch used for? Evercoat Gel Coat Scratch & Patch is a one-part repair product for permanent repairs to hairline cracks, small scratches, and chips. It can be used on fiberglass boats, bathtubs, shower stalls, and hot tubs, and is also suitable for repairing paint, linoleum, Formica, and some plastics.
- Does Evercoat Gel Coat Scratch Patch require a catalyst? No. Evercoat Gel Coat Scratch Patch uses a one-part formula that does not require a catalyst. Apply enough product to fill the scratch or chip, allow it to dry, and remove the excess with the included plastic spreader.
- How do you apply Evercoat Marine Gel Coat Scratch Patch? Use Evercoat Gel Coat Scratch Patch at temperatures of 60°F or above. Clean and completely dry the surface, then fill the scratch or chip with a small excess above and around the repair. Allow it to dry for 15 minutes, remove the excess with the included scraper, and allow the area to dry for another 30 minutes.
- How long should Evercoat Gel Coat Scratch Patch dry before finishing? After application, allow the product to dry for 15 minutes before removing excess material with the included plastic scraper. Then allow the repaired area to dry for an additional 30 minutes before finishing it with a marine wax.
- Is Evercoat Clear Scratch Patch suitable for metal flake finishes? Yes. Evercoat Clear Scratch Patch is ideal for surface scratch repairs on metal flake finishes. The product is available in a 1/2 fl. oz. bottle and includes a spreader for removing excess material.
- How should an Evercoat Gel Coat Scratch Patch repair be cared for after application? After finishing the repaired area with marine wax, avoid washing or scrubbing the area for 3 days. Keep in mind that the color of the product tends to darken after drying.
From $58.99
Premium Marine Polyester Resin
The perfect no-run, no-sag polyester resin for marine repairs! May be used on softwoods and fiberglass. Ideal repair for hulls, decks, cabins and tanks. Repairs all boat surfaces, resists impacts and protects against moisture damage. Use with Sea-Glass fiberglass fabrics and Evercoat Coloring Agents. Liquid hardener included. ***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***
SDS
Frequently Asked Questions
- What is Premium Marine Polyester Resin used for? Premium Marine Polyester Resin is designed for marine repairs on softwoods and fiberglass. It can be used for repairing hulls, decks, cabins, and tanks, and is formulated to resist impacts and protect against moisture damage.
- Can Premium Marine Polyester Resin be used on fiberglass? Yes. Premium Marine Polyester Resin may be used on fiberglass as well as softwoods. It is intended for marine repair applications involving boat surfaces.
- What boat surfaces can Premium Marine Polyester Resin repair? Premium Marine Polyester Resin is suitable for repairs involving hulls, decks, cabins, and tanks. The product description also states that it can be used to repair all boat surfaces.
- Does Premium Marine Polyester Resin include hardener? Yes. Liquid hardener is included with Premium Marine Polyester Resin.
- What fiberglass materials can be used with Premium Marine Polyester Resin? Premium Marine Polyester Resin is intended for use with Sea-Glass fiberglass fabrics. The product description also states that it can be used with Evercoat Coloring Agents.
From $19.99
Coloring Agent for Polyester and Epoxy
Popular color matching agent that blends with polyester resins, epoxy resins, gel paste, polyester fillers, putties and Skid-No-More.
1 oz.
***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***
SDS
$7.99
3 flexible plastic spreaders for fast, clean application of body fillers and putties. Pictured in yellow, but are actually red.
Related collections
Fiberglass Evercoat products currently published by All Marine World.
- Choosing a selection results in a full page refresh.
- Opens in a new window.