EMP

EMP 57-57520 MerCruiser V8 GM Small Block Exhaust Manifold

This exhaust manifold is designed for use with MerCruiser cooling systems and meets OEM specifications.

Exhaust Manifold Application:

• Fits most MerCruiser (GM) small blocks with center riser
• Interchangeable:

BARR Marine

MC-1-87114

GLM

51230

Mercury/MerCruiser

87114A19

Sierra

18-1953-2

Frequently Asked Questions

• What is the EMP 57-57520 MerCruiser V8 GM Small Block Exhaust Manifold used for? The EMP 57-57520 MerCruiser V8 GM Small Block Exhaust Manifold is designed for use with MerCruiser cooling systems. It is manufactured to meet OEM specifications and is intended for most MerCruiser GM small block engines with center riser exhaust manifolds.
• What MerCruiser engines does the EMP 57-57520 exhaust manifold fit? This exhaust manifold fits most MerCruiser GM small block engines with a center riser. The product description does not provide specific horsepower, model year, or serial number ranges, so verify your engine and exhaust manifold configuration before ordering.
• Does the EMP 57-57520 meet OEM specifications? Yes. The EMP 57-57520 MerCruiser V8 GM Small Block Exhaust Manifold is designed for use with MerCruiser cooling systems and meets OEM specifications.
• What part numbers does the EMP 57-57520 MerCruiser exhaust manifold replace? The EMP 57-57520 is interchangeable with BARR Marine MC-1-87114, GLM 51230, Mercury/MerCruiser 87114A19, and Sierra 18-1953-2. Comparing your existing part number with these listed interchange numbers can help confirm the replacement.
• What should I verify before purchasing the EMP 57-57520 exhaust manifold? Verify that your MerCruiser engine is a GM small block with a center riser configuration. Since the description specifies that it fits most, rather than all, MerCruiser GM small blocks, confirm your engine and exhaust manifold configuration before ordering.

EMP 57-57513 MerCruiser V6/V8 Exhaust Center Riser Elbow

This EMP exhaust center riser elbow fits most MerCruiser V6/V8 applications and meets all OEM requirements.

Product Features:

4" Exhaust Outlet

7° Down Angle

Interchangeable

BARR Marine

MC-210-43354

GLM

51140

Mercury/MerCruiser

44354A3

807988A03

Quality Mark

T-20976

Sierra

18-1976-2

For use with:

Manifolds

18-1952-1

18-1953-2

18-1957-1

Exhaust Elbow Gaskets

18-0672

18-0897

18-2849-1

18-2849-9-1

Frequently Asked Questions

• What is the EMP 57-57513 MerCruiser V6/V8 Exhaust Center Riser Elbow used for? The EMP 57-57513 MerCruiser V6/V8 Exhaust Center Riser Elbow is an exhaust elbow designed for most MerCruiser V6/V8 applications. It features a 4-inch exhaust outlet and a 7-degree down angle and is stated to meet all OEM requirements.
• What are the specifications of the EMP 57-57513 Exhaust Center Riser Elbow? The EMP 57-57513 has a 4-inch exhaust outlet and a 7-degree down angle. These specifications identify the exhaust center riser elbow for its listed MerCruiser V6/V8 applications.
• Which manifolds can be used with the EMP 57-57513 Exhaust Center Riser Elbow? The EMP 57-57513 is listed for use with manifolds 18-1952-1, 18-1953-2, and 18-1957-1. Verify your manifold part number before purchasing to confirm that this exhaust elbow is appropriate for your application.
• Which exhaust elbow gaskets are listed for use with the EMP 57-57513? The EMP 57-57513 is listed for use with exhaust elbow gaskets 18-0672, 18-0897, 18-2849-1, and 18-2849-9-1. Check the applicable gasket part number for your specific installation before ordering.
• What part numbers are interchangeable with the EMP 57-57513 Exhaust Center Riser Elbow? The EMP 57-57513 is listed as interchangeable with BARR Marine MC-210-43354, GLM 51140, Mercury/MerCruiser 44354A3 and 807988A03, Quality Mark T-20976, and Sierra 18-1976-2.

EMP 50-75415 Mercury-Mercruiser Starter Motor

Fits:

75 EFI (4-STROKE) - 1B366823 THRU 2B094995

80 EFI (4-STROKE) - 0P459572 THRU 2B094995

80 EFI (4-STROKE) - 1B366823 THRU 2B094995

90 EFI (4-STROKE) - 1B366823 THRU 2B094995

100 EFI (4-STROKE) - 0P459572 THRU 2B094995

100 EFI (4-STROKE) - 1B366823 THRU 2B094995

115 EFI (4-STROKE) - 1B366823 THRU 2B094995

Replaces:

Mercury 50-879345T77

EMP 50-35863 Volvo/MerCruiser Boat Starter

This EMP electric starter is an aftermarket replacement engine part for MerCruiser, Volvo, and OMC.

Boat Starter Application:

• For MerCruiser engines with 14" flywheels, 11 tooth and offset bolt pattern.
• For Volvo 1989 & Later 4.3L, V6 & 5.0-7.4L, V8 GM gas engines
• For OMC 1995-98 4.3L, B6, 150-65HP ; 5.0-7.4L V8, 185-330 HP GM engines
• Replaces:

MerCruiser

Volvo

OMC

812428A3

872394

3855177

812604A2

3856004

3854751

822330A2

3857625

864340A2

Interchange:

Sierra

18-5913-1

ARCO

30470

Boat Starter Motor Installation Instructions

These instructions provide a general procedure to the removal and installation of the starter. Refer to the vessel manufacturer's repair manual for detailed instructions. Check and follow all safety precautions outlined in the vessel manufacturer's repair manual.

WARNING: Disconnect the battery cables starting with the negative cable prior to removal of starter to eliminate electrical shock hazard.

Before Replacing the Starter

Verify the Starter is nonfunctional. It can be tested using a voltmeter, carbon pile load tester and clamp-on style ammeter.

Verify the batteries are fully charged and battery terminals are clean and firmly in place. Check battery cable for tears or signs of corrosion.

Verify all fuses are good

Check all wiring connections leading to the starter for cracks, discoloration, or signs of overheating. If any are present the connections must be replaced.

Boat Starter Removal Instructions

Ensure the ignition is off and remove the negative (ground) battery cable from the battery

Disconnect all wire connections and plugs from the starter. Note their location and identify each one. This will help make installation of the replacement easier.

Loosen the starter mounting bolts. For easier installation of the replacement starter note the location of any shims, heat shields, and support brackets.

Remove mounting bolts, tilt, or rotate starter to clear flywheel and transmission housing and remove starter from the vessel. Note positions of any shims. Shims can be stuck to either the engine mounting or the mounting pads of the starter

Inspect starter drive teeth for damaged pinions. If drive is damaged it is important to inspect the flywheel or ring gear for broken or worn teeth. A broken or worn ring gear must be replaced or it will cause damage to the new starter and void the manufacturer's warranty.

New Boat Starter Installation Instructions

Check and compare the original starter to the replacement. All wire connectors, plug connectors, hardware, and mounting holes should be compatible.

Install the replacement starter reusing all mounting hardware from the original starter. Refer to the vessel repair manual for the torque nuts and bolts that meet the manufacturer's required specifications

Reconnect all electrical connections of the replacement starter to the correct terminals. Ensure all connectors are clean and fit properly.

Reconnect the battery cable starting with the positive connections first.

Place the removed starter in the replacement starter box for proper core return.

Frequently Asked Questions

• What is the EMP 50-35863 Volvo/MerCruiser Boat Starter used for? The EMP 50-35863 is an aftermarket replacement starter for select MerCruiser, Volvo, and OMC marine engines. It is designed for MerCruiser engines with 14" flywheels, 11-tooth starters, and an offset bolt pattern, with additional applications listed for Volvo and OMC GM gas engines.
• What MerCruiser engines does the EMP 50-35863 Boat Starter fit? The EMP 50-35863 Boat Starter is specified for MerCruiser engines with 14" flywheels, 11 teeth, and an offset bolt pattern. It replaces listed MerCruiser starter numbers including 812428A3, 812604A2, 822330A2, and 864340A2. What Volvo and…

EMP 50-02842 BRP Boat Starter

This EMP boat starter is an aftermarket replacement engine part for BRP V4, 90-115HP Outboards with 10 tooth gear.

Replaces:

BRP

586283

Interchangeable:

Sierra

18-5634

API Marine

MOT2003N

ARCO

5372

Mallory

9-15007

MES

S2066M

Boat Starter Motor Installation Instructions

These instructions provide a general procedure to the removal and installation of the starter. Refer to the vessel manufacturer's repair manual for detailed instructions. Check and follow all safety precautions outlined in the vessel manufacturer's repair manual.

WARNING: Disconnect the battery cables starting with the negative cable prior to removal of starter to eliminate electrical shock hazard.

Before Replacing the Starter

Verify the Starter is nonfunctional. It can be tested using a voltmeter, carbon pile load tester and clamp-on style ammeter.

Verify the batteries are fully charged and battery terminals are clean and firmly in place. Check battery cable for tears or signs of corrosion.

Verify all fuses are good

Check all wiring connections leading to the starter for cracks, discoloration, or signs of overheating. If any are present the connections must be replaced.

Boat Starter Removal Instructions

Ensure the ignition is off and remove the negative (ground) battery cable from the battery

Disconnect all wire connections and plugs from the starter. Note their location and identify each one. This will help make installation of the replacement easier.

Loosen the starter mounting bolts. For easier installation of the replacement starter note the location of any shims, heat shields, and support brackets.

Remove mounting bolts, tilt, or rotate starter to clear flywheel and transmission housing and remove starter from the vessel. Note positions of any shims. Shims can be stuck to either the engine mounting or the mounting pads of the starter

Inspect starter drive teeth for damaged pinions. If drive is damaged it is important to inspect the flywheel or ring gear for broken or worn teeth. A broken or worn ring gear must be replaced or it will cause damage to the new starter and void the manufacturer's warranty.

New Boat Starter Installation Instructions

Check and compare the original starter to the replacement. All wire connectors, plug connectors, hardware, and mounting holes should be compatible.

Install the replacement starter reusing all mounting hardware from the original starter. Refer to the vessel repair manual for the torque nuts and bolts that meet the manufacturer's required specifications

Reconnect all electrical connections of the replacement starter to the correct terminals. Ensure all connectors are clean and fit properly.

Reconnect the battery cable starting with the positive connections first.

Place the removed starter in the replacement starter box for proper core return.

EMP 50-02829 OMC/Volvo Boat Starter

This EMP electric starter is an aftermarket replacement engine part for Volvo, OMC, and Chrysler inboards.

Boat Starter Application:

For Chrysler inboard 4-Cyl engines. 9 tooth gear

For Volvo 1995-1998 GM 4-Cyl engines 9 tooth gear

For OMC 1994 4-Cyl 130HP GM engines. 9 tooth gear

This model replaces older clockwise rotation 10MT starters, as well as other clockwise 10MT starters with one long and one short bold-straight across pattern.

The OE version uses a 9 tooth drive while this aftermarket uses an 11 tooth drives but will work interchangeable with no modifications required.

Replaces:

Volvo

OMC

Chrysler

3862308

988217

MS21

3856003

3855882

3850526

988218

982121

Interchange:

Sierra

18-5919-1

API Marine

10064

10096

ARCO

30460

Mallory

9-15903

9-15901

MES

5401M

Boat Starter Motor Installation Instructions

These instructions provide a general procedure to the removal and installation of the starter. Refer to the vessel manufacturer's repair manual for detailed instructions. Check and follow all safety precautions outlined in the vessel manufacturer's repair manual.

WARNING: Disconnect the battery cables starting with the negative cable prior to removal of starter to eliminate electrical shock hazard.

Before Replacing the Starter

Verify the Starter is nonfunctional. It can be tested using a voltmeter, carbon pile load tester and clamp-on style ammeter.

Verify the batteries are fully charged and battery terminals are clean and firmly in place. Check battery cable for tears or signs of corrosion.

Verify all fuses are good

Check all wiring connections leading to the starter for cracks, discoloration, or signs of overheating. If any are present the connections must be replaced.

Boat Starter Removal Instructions

Ensure the ignition is off and remove the negative (ground) battery cable from the battery

Disconnect all wire connections and plugs from the starter. Note their location and identify each one. This will help make installation of the replacement easier.

Loosen the starter mounting bolts. For easier installation of the replacement starter note the location of any shims, heat shields, and support brackets.

Remove mounting bolts, tilt, or rotate starter to clear flywheel and transmission housing and remove starter from the vessel. Note positions of any shims. Shims can be stuck to either the engine mounting or the mounting pads of the starter

Inspect starter drive teeth for damaged pinions. If drive is damaged it is important to inspect the flywheel or ring gear for broken or worn teeth. A broken or worn ring gear must be replaced or it will cause damage to the new starter and void the manufacturer's warranty.

New Boat Starter Installation Instructions

Check and compare the original starter to the replacement. All wire connectors, plug connectors, hardware, and mounting holes should be compatible.

Install the replacement starter reusing all mounting hardware from the original starter. Refer to the vessel repair manual for the torque nuts and bolts that meet the manufacturer's required specifications

Reconnect all electrical connections of the replacement starter to the correct terminals. Ensure all connectors are clean and fit properly.

Reconnect the battery cable starting with the positive connections first.

Place the removed starter in the replacement starter box for proper core return.

EMP 47-47292 Volvo Impeller

This impeller is intended for use on Volvo engines and meets all OEM requirements.

Specification:

ID: 14.29mm

OD: 57mm

W: 32.5mm

12 Blades

Spline Hub

Impeller Application:

• For 1965 & later 3.0L 4-Cyl 135-150 HP; 4.3L 6-Cyl 205-225HP; 5.0-8.2L V8 270-415HP Engines
• Replaces:

Volvo

21213660

Interchangeable:

Sierra

18-3276-1

EMP 47-09201 MerCruiser Impeller Kit

This impeller Kit is intended for use on MerCruiser engines and meets all OEM requirements.

Specifications:

Double Flat Drive Hub

8 Blades

ID: 11.4mm

OD: 66.5mm

W: 50.6mm

Impeller Kit Application:

• For MerCruiser 1988/2007-08 V8 390HP Bravo Water Pumps
• Replaces:

Mercury

8M0104229

862232A2

Interchangeable:

Sierra

18-3016-1

GLM

89700

Mallory

9-45310

EMP 47-03908 MerCruiser Impeller

This impeller is intended for use on MerCruiser engines and meets all OEM requirements.

Specification:

ID: 13mm

OD: 58.8mm

W: 50.6mm

8 Blades

Single Flat Drive Hub

Impeller Application:

• For 1997-2010 MerCruiser V6 155-175HP; V8 Bravo, SSM, Dry Six, M6 & NXT drive water pumps
• Replaces:

Mercury

59362T1

593621

59362B1

59362

59362A1

Interchangeable:

Sierra

18-3087

GLM

89740

Mallory

9-45375

EMP 47-01814 Mercury Mariner Impeller

This impeller is intended for use on Mercury Mariner, Honda, and Force engines and meets all OEM requirements.

Specification:

ID: 22.4mm

OD: 89mm

W: 32.5mm

6 Blades

Uses Key 28-32833

Impeller Application:

• For Mercury Mariner 1988-2001 3-Cyl 30-115HP; 4-Cyl 40-125HP; V6 200-300 HP outboards
• For Honda 1997-1998 BF Series 4-Cyl 75-90HP outboard water pumps
• For Force 1995-1999 Force 3-Cyl 75-90HP; 4-Cyl 120HP outboard water pumps
• Replaces:

Mercury

43026T2

43026B2

430264

430262

430261

Force

430262

Honda

19210-ZW1-303

Interchangeable:

Sierra

18-3056

GLM

89630

Mallory

9-45307

EMP 47-00001 Mercury MerCruiser Impeller

This impeller is intended for use on Mercury, MerCruiser, and Force engines and meets all OEM requirements.

Specification:

ID: 22.3mm

OD: 60mm

W: 33.8mm

6 Blades

Uses Key 28-23834

Impeller Application:

• For 1967-2006 Mercury Mariner 4-Cyl 65-85 HP; 6-Cyl 90-150 HP; V6 135-225 HP outboard water pumps
• For 1983-90 MerCruiser R/MR/Alpha One water pumps
• For 1989-1994 Force 3-Cyl 85-90 HP; 4-Cyl 120-125 HP; 5-Cyl 150 HP outboard water pumps
• Replaces:

Mercury

89984T4

89984B2

899844

899842

89984

65960

85460

30221

Force

89984T3

803631T

F694065

Interchangeable:

Sierra

18-3017

GLM

89840

Mallory

9-45306

EMP 46-46502 Mercury MerCruiser Water Pump Kit with Housing

This EMP replacement water pump kit is for use with Mercury and MerCruiser engines. This boat water pump kit comes with a rubber coated wear plate, stainless steel housing, impeller, and various hardware.

Water Pump Application Information:

• For MercCruiser Alpha Gen II 1991 & Later
• For Mercury 1989-1998 Mercury/Mariner 3-Cyl 30-105; 4-Cyl 75-120; V6 200-250 HP Outboards
• Replaces:

Mercury

817275Q05

817275Q4

817275A5

817275A4

817275A3

Interchange:

Sierra

18-3147

GLM

12414

Mallory

9-48315

EMP 46-46501 Mercury MerCruiser Water Pump Kit

This EMP replacement water pump kit is for use with Mercury and MerCruiser engines. This boat water pump kit comes with a rubber coated wear plate, stainless steel housing, impeller, and various hardware.

Water Pump Application Information:

• For MercCruiser Alpha Gen II 1991 & Later
• For Mercury 1989-2010 Mercury/Mariner 3-Cyl 30-105; 4-Cyl 75-120; V6 200-250 HP Outboards
• Replaces:

Mercury

817275A4

817275A3

Interchange:

Sierra

18-3570

GLM

12416

EMP 46-46004 Yamaha Water Pump Kit

This EMP replacement water pump kit is for use with Yamaha engines.

This water pump is designed for use with 1984 & Later 60-90 HP Yamaha outboards.

Replaces:

Yamaha

692-W0078-A0-00

Interchange:

Sierra

18-3371

GLM

12053

Mallory

9-48616

EMP 46-13251 Volvo Penta Sea Water Pump Replaces 21212799

This EMP sea water pump is designed as a replacement for Volvo Penta 21212799.

Frequently Asked Questions

• What is the EMP 46-13251 Volvo Penta Sea Water Pump used for? The EMP 46-13251 Volvo Penta Sea Water Pump is designed as a replacement for Volvo Penta part number 21212799.
• What Volvo Penta part does the EMP 46-13251 Sea Water Pump replace? The EMP 46-13251 Volvo Penta Sea Water Pump replaces Volvo Penta 21212799.
• Is the EMP 46-13251 Sea Water Pump a replacement part? Yes. The EMP 46-13251 is specifically described as a replacement sea water pump for Volvo Penta 21212799.

EMP 46-13171 Mercury Mariner Water Pump Kit with Base

This EMP replacement water pump kit is for use with Mercury Mariner engines.

Water Pump Application Information:

• For Mercury Mariner:

105 Jet 0D182000 & UP

V 135 904646 & UP

140 Jet 0D082000 & UP

V 150 A904646 & UP

V 175 6618751 & UP

V 200 6625221 & UP

V 220 ALL 18-3017

Replaces:

Mercury Marine

46-42579A4

46-96148A8

46-96148A5

46-44292A4

46-48747A3

46-57234A3

46-58618A4

46-60367A1

46-37433A1

46-60367A4

46-32437A1

46-64141A11

46-73802A3

46-73804A3

46-69222A3

46-78400A2

MerCruiser Stern Drive

46-32437A3

96-96148A8

46-37433A1

Interchange:

Mallory

9-48306

Sierra

18-3319

EMP 46-13159 MerCruiser Water Pump Kit

This EMP replacement water pump kit is for use with MerCruiser engines.

Water Pump Application Information:

• For MercCruiser V8 200-575HP engines, Alpha One, Alpha Gen II, Bravo, SSM, & Dry Six drive water pumps
• Replaces:

Mercury

807151A14

Interchange:

Sierra

18-3150

GLM

12392

Mallory

9-48350

Frequently Asked Questions

• What is the EMP 46-13159 MerCruiser Water Pump Kit used for? The EMP 46-13159 MerCruiser Water Pump Kit is a replacement water pump kit designed for use with MerCruiser engines. It is specified for MerCruiser V8 engines rated from 200-575 HP and for Alpha One, Alpha Gen II, Bravo, SSM, and Dry Six drive water pump applications.
• Which MerCruiser engines and drives fit the EMP 46-13159 Water Pump Kit? The EMP 46-13159 is specified for MerCruiser V8 200-575 HP engines and water pumps used with Alpha One, Alpha Gen II, Bravo, SSM, and Dry Six drives. Verify your engine and drive application before purchasing to confirm compatibility.
• What Mercury part number does the EMP 46-13159 replace? The EMP 46-13159 replaces Mercury part number 807151A14. If your existing water pump kit carries this part number, verify the application information before selecting the EMP replacement.
• Is the EMP 46-13159 interchangeable with Sierra 18-3150? Yes. The product description lists Sierra 18-3150 as an interchangeable part number for the EMP 46-13159 MerCruiser Water Pump Kit. It is also listed as interchangeable with GLM 12392 and Mallory 9-48350.
• What part numbers interchange with the EMP 46-13159 MerCruiser Water Pump Kit? The EMP 46-13159 is interchangeable with Sierra 18-3150, GLM 12392, and Mallory 9-48350. It replaces Mercury 807151A14. Verify your existing part number and specific engine or drive application before purchasing.

EMP 46-07300 BRP Complete Water Pump Kit

This EMP replacement water pump kit is for use with BRP engines.

Water Pump Application Information:

• For BRP V4 90-140HP; V6 150-225HP; V8 250-300HP outboard water pumps with housing that do NOT contain a bleed/relief hole. If your housing has a bleed hole use water pump kit 46-00013
• Replaces:

Johnson/Evinrude

5001595

435929

Interchange:

Sierra

18-3315-2

GLM

12000

Mallory

9-48200

EMP 46-02855 BRP Water Pump Kit with Housing

This EMP replacement water pump kit is for use with BRP engines.

Water Pump Application Information:

• For 1974-2001 BRP (Johnson/Evinrude) 2-Cyl 5-15HP Outboards
• Replaces:

BRP

394711

391698

388139

393560

387610

391388

389112

318999

319989

386697

386886

386685

318875

Interchange:

Sierra

18-3327

GLM

12050

Mallory

9-48201

EMP 46-00091 Mercury MerCruiser Impeller Service Kit

This impeller service kit is intended for use on Mercury and MerCruiser engines and meets all OEM requirements.

Impeller Service Kit Application:

• For 1999-2006 Mercury Mariner V6 135-225HP Outboards
• For 1978-1990 MerCruiser MC-1 & R/MR/Alpha One water pumps
• Replaces:

Mercury

89984Q5

89984T6

Interchangeable:

Sierra

18-3217

GLM

12290

Mallory

9-48304

EMP 46-00090 Mercury MerCruiser Water Pump Kit with Housing

This EMP replacement water pump kit is for use with Mercury and MerCruiser engines.

Water Pump Application Information:

• For MerCruiser MC1 & R/MR/Alpha One engines
• For Mercury Mariner V6 135-225HP outboards
• Replaces:

Mercury

96148Q8

96148A8

96148A8

96148A5

96148B8

58618A4

64141A11

78400A2

73802A3

73802A3

73804A3

96148B5

57234A3

60367A4

48747A3

44292A4

42579A4

69222A3

Interchange:

Sierra

18-3517

GLM

12280

Mallory

9-48311

EMP 46-00013 BRP Complete Water Pump Kit

This EMP replacement water pump kit is for use with BRP engines.

Water Pump Application Information:

• For 1979-2006 BRP (Johnson/Evinrude) 4-Cyl 65-140 HP, 6-Cyl, 150-235 HP, V8, 250-300
• Replaces:

BRP

5001594

434421

435447

395062

395060

393082

392750

391637

390768

Interchange:

Sierra

18-3392

GLM

12104

12102

Mallory

9-48210

9-48203

EMP 35-57824 Mercury Oil Filter

Fits:

175, 200 HP 3.4L V6 (Four Stroke)

200, 225, 300 HP 4.6L V8 (Four Stroke)

450 HP V8 (Racing) Verado Outboard

Replaces:

Mercury 8M0123025

Sierra 18-8703

EMP 35-57822 Mercury Marine Oil Filter replaces 35-877761K01

This EMP oil filter is designed as an aftermarket replacement Mercury Marine Engine Part. The strong metal base plates and end caps provide excellent corrosion resistance in marine environments. A high effieciency glass media helps trap dirt and other contaminants to provide a cleaner and longer service life.

EMP Oil Filter Application:

• For Mercury Marine 2006-2016 4-Cyl 75-115HP; V6 150HP outboards
• Interchange:

Sierra

18-7758

Mallory

9-57822

Mercury Marine

35-877761K01

35-877761Q01