{"product_id":"trac-trolling-motor-rigging-kit","title":"Trac Outdoor Trolling Mtr Rigging Kit","description":"\u003cp\u003eTRAC 69440 Trolling Motor Rigging Kit\u003c\/p\u003e\u003cp\u003eThe Trac Trolling Motor Rigging Kit has everything you need to wire your boat for high-current (60 amp) 12v\/24v and now up to 36v power! You can use this as a high current power connection for any boat to power 12v-36v trolling motors, winches are any other 12v-36v devices up to 60 amps.\u003c\/p\u003e\u003cp\u003eThis Trolling Motor Kit Includes:\u003c\/p\u003e\u003cp\u003eTRAC 12\/24v\/36v high-current Quick-Connect system:\u003c\/p\u003e\u003cp\u003e2 Quick-Connect plugs (one for boat and one for trolling motor or other device)\u003c\/p\u003e\u003cp\u003e1-½” Round Hole Adaptor (to install boat plug in flat panel – option 1)\u003c\/p\u003e\u003cp\u003eU-bracket (to install boat plug on flat surface – option 2)\u003c\/p\u003e\u003cp\u003e30’ Heavy 8-gauge AWG Tin-Plated Marine-Grade Positive (red) Battery Wire\u003c\/p\u003e\u003cp\u003e30’ Heavy 8-gauge AWG Tin-Plated Marine-Grade Negative (black) Battery Wire\u003c\/p\u003e\u003cp\u003e2-14” 8-gauge Cross-over Wires for 24v and 36v systems\u003c\/p\u003e\u003cp\u003eAll Heat-shrink Terminations included or installed\u003c\/p\u003e\u003cp\u003e28’ of Corrugated Wire Loom\u003c\/p\u003e\u003cp\u003eHigh-current 60 amp Manual Resetting Circuit Breaker\u003c\/p\u003e\u003cp\u003e4 Isolator Bolts to install Trolling Motor or other device\u003c\/p\u003e\u003cp\u003eReplaces old TRAC part # T10141\u003c\/p\u003e\u003cp\u003eHow to Install TRAC Trolling Motor Rigging Kit\u003c\/p\u003e\u003cp\u003eKit Includes:\u003c\/p\u003e\u003cp\u003eTrac 12\/24\/36v high-current Quick-Connect System:\u003c\/p\u003e\u003cp\u003e2 Quick-Connect plugs (one for boat and one for trolling motor or other device)\u003c\/p\u003e\u003cp\u003e1-1\/2” Round Hole Adaptor (to install boat plug in flat panel – option 1)\u003c\/p\u003e\u003cp\u003eU-bracket (to install boat plug on flat surface – option 2)\u003c\/p\u003e\u003cp\u003e30’ Heavy 8-gauge AWG Tin-Plated Marine-Grade Positive (red) Battery Wire\u003c\/p\u003e\u003cp\u003e30’ Heavy 8-gauge AWG Tin-Plated Marine-Grade Negative (black) Battery Wire\u003c\/p\u003e\u003cp\u003eTwo 14” 8-gauge Cross-over Wires for 24 and 36v systems\u003c\/p\u003e\u003cp\u003eAll Heat-shrink Terminations included or installed\u003c\/p\u003e\u003cp\u003e28’ of Corrugated Wire Loom\u003c\/p\u003e\u003cp\u003eHigh-current 60 amp Manual Resetting Thermal Circuit Breaker\u003c\/p\u003e\u003cp\u003e4 Isolator Bolts to install Trolling Motor or other device\u003c\/p\u003e\u003cp\u003eInstallation Instructions for Battery End of Harness (plug with long wire harness)\u003c\/p\u003e\u003cp\u003eRoute the wiring harness along or through boat from the panel position to the battery position. You will pass the two wires (positive wire has ring termination already installed and negative wire is cut) through your boat to the battery.\u003c\/p\u003e\u003cp\u003eMake a small coil in the wire at the panel end to leave a little extra wire. Better to leave extra wire than find out the wires are a little short.\u003c\/p\u003e\u003cp\u003ePosition loom (black corrugated plastic tubing) along a location where it can be secured with cable-ties (zip ties) or otherwise be protected. Wires should not touch sharp metal or anything that might wear through the insulation.\u003c\/p\u003e\u003cp\u003eThe circuit breaker should be installed as close to the battery positive (+) terminal as possible. The circuit breaker can hang freely, only supported by the positive wire; however, it is best if the circuit breaker is secured to a bulkhead with screws.\u003c\/p\u003e\u003cp\u003eNOTE: Never install the circuit breaker on the negative wire – only the positive wire can be used.\u003c\/p\u003e\u003cp\u003ePosition the battery positive wire (red) at the battery positive (+) terminal and route the wire from the terminal to the gray end cap of the circuit breaker. If the circuit breaker is secured with screws to a bulk head, route the wire from battery and add a loop of wire like you did at the panel end.\u003c\/p\u003e\u003cp\u003eCut the battery positive wire length so there is enough wire to run from the battery positive post, making a loop and reaching one end of the circuit breaker. (It does not matter which end of the circuit breaker is used).\u003c\/p\u003e\u003cp\u003eAfter the battery positive wire is cut, strip ½” of the plastic insulation away from both ends of each piece of battery positive wire. Unscrew the gray end caps on the circuit breaker.\u003c\/p\u003e\u003cp\u003ePlace the end caps onto each piece of wire. Place the red grommet over each piece of wire.\u003c\/p\u003e\u003cp\u003eUser an Allen wrench to unscrew the set screw on the circuit breaker terminals.\u003c\/p\u003e\u003cp\u003eInsert the stripped wire and tighten the set screws. Slide the gray end caps up to the circuit breaker …\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":50584355307778,"sku":"TRC-69440","price":267.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0842\/3024\/2562\/files\/69440__41418.1737849825.jpg?v=1791101848","url":"https:\/\/allmarineworld.com\/products\/trac-trolling-motor-rigging-kit","provider":"All Marine World","version":"1.0","type":"link"}