{"product_id":"trac-outdoor-vehicle-wiring-kit","title":"Trac Outdoor Vehicle Wiring Kit","description":"\u003cp\u003eTRAC 69140 Outdoor Vehicle Wiring Kit\u003c\/p\u003e\u003cp\u003eThe TRAC 69140 Vehicle Wiring Kit has everything you need to wire your vehicle for high-current (60 amp) 12v power. This 12v high current power connection can be used for trailer winch, portable winch and any other 12v device up to 60 amps.\u003c\/p\u003e\u003cp\u003eKit Includes:\u003c\/p\u003e\u003cp\u003eTRAC 12v high-current Quick-Connect system:\u003c\/p\u003e\u003cp\u003e2 Quick-Connect plugs (one for rear of vehicle and one for trailer winch or any other 12v device)\u003c\/p\u003e\u003cp\u003e1½” Round Hole Adaptor (for installation on flat panel – option 1)\u003c\/p\u003e\u003cp\u003eU-bracket (for installation on flat surface – option 2)\u003c\/p\u003e\u003cp\u003e25’ Heavy 8-gauge AWG Tin-Plated Marine-Grade Positive (red) Battery Wire\u003c\/p\u003e\u003cp\u003e5’ Heavy 8-gauge AWG Tin-Plated Marine-Grade Negative (black) Battery Wire\u003c\/p\u003e\u003cp\u003eCorrosion resistant self-tapping grounding bolt to attach negative wire to vehicle frame\u003c\/p\u003e\u003cp\u003eHigh-current 60 amp Manual Resetting Circuit Breaker\u003c\/p\u003e\u003cp\u003eCable ties to secure wires to vehicle undercarriage.\u003c\/p\u003e\u003cp\u003eHow to Install TRAC 69140 Vehicle Wiring Kit\u003c\/p\u003e\u003cp\u003eInstallation for Battery End of Harness\u003c\/p\u003e\u003cp\u003eRoute the red positive wire along or through your vehicle from the rear of the vehicle (or the position where you choose to locate the 12v receptacle) to the battery positive terminal.\u003c\/p\u003e\u003cp\u003eThe black negative wire will be grounded to the vehicle frame near the 12v receptacle.\u003c\/p\u003e\u003cp\u003eRoute and position the battery wires in a safe place and secure with cable ties (zip ties). The wires should not be touching any sharp metal edge or anything that might wear the insulation off the wiring.\u003c\/p\u003e\u003cp\u003eThe circuit breaker should be installed as close to the battery positive (+) terminal as possible and no more than 12” (30.5 cm) away from the battery positive terminal. The circuit breaker should be secured to the firewall or other surface with screws.\u003c\/p\u003e\u003cp\u003eNEVER install the circuit breaker on the negative wire. Only the positive wire can be used.\u003c\/p\u003e\u003cp\u003ePosition the red battery positive ring termination at the battery positive (+) terminal and route the wire from the terminal to the gray end cap of the circuit breaker.\u003c\/p\u003e\u003cp\u003eAdd an extra couple pf inches or a loop of wire to provide a little extra wire for working on the system and in case a change of location is required.\u003c\/p\u003e\u003cp\u003eCut the battery positive wire so there is enough wire to run from the battery positive post, making a loop and reaching one end of the circuit breaker.\u003c\/p\u003e\u003cp\u003eIt does not matter which end of the circuit breaker is used.\u003c\/p\u003e\u003cp\u003eAfter the battery positive wire is cut, strip ½ (12.7mm) of the plastic insulation away from each end of battery positive wire.\u003c\/p\u003e\u003cp\u003eUnscrew the grey end caps on the circuit breaker and place the end cap onto each piece of wire.\u003c\/p\u003e\u003cp\u003ePlace the red grommet in each piece of wire. Use an Allen wrench to unscrew the set screw on the circuit breaker terminals. Insert the stripped wire into the circuit breaker terminal. Tighten the set screw.\u003c\/p\u003e\u003cp\u003eSlide the gray end cap up to the circuit breaker and screw on. The red grommet should fit well in the gray cap as it is screwed on. Tighten finger-tight only. The red grommet and an O-ring will seal the connection. Do this on both sides of the circuit breaker.\u003c\/p\u003e\u003cp\u003eNOTE: Do not connect the positive wire to the battery yet.\u003c\/p\u003e\u003cp\u003eInstallation for Rear of Vehicle\u003c\/p\u003e\u003cp\u003eThe wiring harness should now be routed along or through your vehicle from the battery position to the rear or your chosen location for the 12v receptacle.\u003c\/p\u003e\u003cp\u003eChoose the type of receptacle installation that is best for your application:\u003c\/p\u003e\u003cp\u003eThe round hole adaptor can be used for installations through a flat panel.\u003c\/p\u003e\u003cp\u003eThe U-bracket can be used to install the receptacle on the side of a flat surface.\u003c\/p\u003e\u003cp\u003eThe receptacle (or plug) can also be unattached if desired, but make sure it is secured and not able to touch the ground or be damaged in any way.\u003c\/p\u003e\u003cp\u003eThe wiring harness positive and negative wires can be cut to length, but can also be coiled to the access wire and secured with cable ties (zip ties).\u003c\/p\u003e\u003cp\u003eU-Bracket Installation\u003c\/p\u003e\u003cp\u003eThe bracket will …\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":50584347246850,"sku":"TRC-69140","price":174.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0842\/3024\/2562\/files\/69140__30427.1737896645.webp?v=1791101830","url":"https:\/\/allmarineworld.com\/products\/trac-outdoor-vehicle-wiring-kit","provider":"All Marine World","version":"1.0","type":"link"}