{"product_id":"trac-g2-anchor-winch-second-switch-kit","title":"Trac Outdoor ANCHOR WINCH 2ND SWITCH KIT-G2","description":"\u003cp\u003eTRAC G2 Anchor Winch Second Switch Kit\u003c\/p\u003e\u003cp\u003ePre-made cables with connectors, sealed switch and bezel faceplate – everything needed to install an auxiliary control switch in the location of your choice.\u003c\/p\u003e\u003cp\u003eThis switch to be installed at the helm or wherever you choose, provides a second option for control of the electric anchor winch. The switch on the winch cover will continue to operate as well.\u003c\/p\u003e\u003cp\u003eThis second switch kit works with all TRAC anchor winches -- fresh and salt water models\u003c\/p\u003e\u003cp\u003eKit Includes:\u003c\/p\u003e\u003cp\u003e24’ Wiring Harness\u003c\/p\u003e\u003cp\u003eSwitch\u003c\/p\u003e\u003cp\u003eSwitch Plate\u003c\/p\u003e\u003cp\u003e4 Screws\u003c\/p\u003e\u003cp\u003eInstallation:\u003c\/p\u003e\u003cp\u003eRemove winch cover and disconnect the switch from the control unit. Be very careful not to pull the wires out of the switch or control unit.\u003c\/p\u003e\u003cp\u003eOne end of the wiring harness has two connectors. Connect them to the switch on winch housing and to the control unit.\u003c\/p\u003e\u003cp\u003eRoute the wiring harness (the end with one connector) to second switch location. The wiring harness is 24’ long.\u003c\/p\u003e\u003cp\u003eIf it is not long enough, you will need to splice-in more wire.\u003c\/p\u003e\u003cp\u003eIf too long, just coil the extra wire and secure it with cable-ties.\u003c\/p\u003e\u003cp\u003eTo install the 2nd switch in desired location, you will need to make a rectangular hole – 1.25” wide by 2.25” high. Fit the switch in the hole to check fit (trim hole as needed) and mark the four screw locations.\u003c\/p\u003e\u003cp\u003eDrill four screw holes with 1\/8” drill bit. Pass the connector thru the hole in the back side.\u003c\/p\u003e\u003cp\u003eConnect the harness connector to the switch connector.\u003c\/p\u003e\u003cp\u003eFit switch plate in the hole and attach with the four screws provided.\u003c\/p\u003e\u003cp\u003eClick here to download Trac Anchor Winch 2nd Switch Kit Installation Instructions\u003c\/p\u003e\u003cp\u003eInformation sourced from TRAC Anchor Winch 2nd Switch Kit Installation Instructions\u003c\/p\u003e\u003cp\u003eFrequently Asked Questions\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eWhat is the TRAC G2 Anchor Winch Second Switch Kit designed for? The TRAC G2 Anchor Winch Second Switch Kit adds an auxiliary control switch for a TRAC electric anchor winch. The additional switch can be installed at the helm or another location of your choice, while the original switch on the winch cover continues to operate the winch.\u003c\/li\u003e\n\u003cli\u003eWhat TRAC anchor winches are compatible with this second switch kit? This second switch kit works with all TRAC anchor winches, including both freshwater and saltwater models. The kit provides a second control location while retaining operation from the switch mounted on the winch cover.\u003c\/li\u003e\n\u003cli\u003eWhat is included with the TRAC G2 Anchor Winch Second Switch Kit? The kit includes a 24-foot wiring harness, a switch, a switch plate, and four screws. The wiring harness comes with connectors to connect the existing winch switch and control unit to the auxiliary switch location.\u003c\/li\u003e\n\u003cli\u003eHow long is the wiring harness included with the TRAC G2 Anchor Winch Second Switch Kit? The wiring harness is 24 feet long, allowing the second switch to be routed to a location of your choice. If additional length is needed, the instructions specify splicing in more wire. If the harness is too long, the extra wire can be coiled and secured with cable ties.\u003c\/li\u003e\n\u003cli\u003eWhat size opening is needed to install the second switch? Installation requires a rectangular opening measuring 1.25 inches wide by 2.25 inches high. After checking the switch fit and trimming the opening as needed, the instructions call for four screw holes drilled with a 1\/8-inch drill bit to secure the switch plate.\u003c\/li\u003e\n\u003cli\u003eCan the second switch be installed at the helm? Yes. The second switch can be installed at the helm or wherever you choose. The wiring harness is routed from the winch to the selected switch location, where it connects to the auxiliary switch. The original switch on the winch cover remains functional after the second switch is installed.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":50584345313538,"sku":"TRC-69040","price":57.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0842\/3024\/2562\/files\/2__27528.1756133917.webp?v=1791101815","url":"https:\/\/allmarineworld.com\/products\/trac-g2-anchor-winch-second-switch-kit","provider":"All Marine World","version":"1.0","type":"link"}