{"product_id":"seastar-outboard-hydraulic-steering-hose-kit","title":"Teleflex Marine SeaStar Outboard Hydraulic Steering Hose Kit","description":"\u003cp\u003eSeaStar Outboard Hydraulic Steering Hose Kit\u003c\/p\u003e\u003cp\u003eIncludes two hoses - can be used with all SeaStar systems, except SeaStar PRO, BayStar, Capilano, and and 3-line inboard systems.\u003c\/p\u003e\u003cp\u003eComes with two hoses\u003c\/p\u003e\u003cp\u003eDesigned to Exceed SAE and ABYC Specifications and Provide Precise Steering Control\u003c\/p\u003e\u003cp\u003eKink and Abrasion Resistant\u003c\/p\u003e\u003cp\u003eSupplied with pre-attached hose fittings on both ends\u003c\/p\u003e\u003cp\u003eHow to Measure Hydraulic Hoses\u003c\/p\u003e\u003cp\u003eNew Installation:\u003c\/p\u003e\u003cp\u003eMeasure hose routing path from wheel center line to engine connection, as follows:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eA = Center line of wheel to gunwale (or deck, if routed downward),B = Dash to transom,C = Gunwale to centerline of cable connection at centered tiller.\u003c\/li\u003e\n\u003cli\u003eMost cylinders move with the engine\/rudder; enough slack must be left in hoses\/tubing to prevent sharp bends (less than 3” radius) and\/or kinking.\u003c\/li\u003e\n\u003cli\u003eWhere rigid tubing is used, flexible hoses must be installed between tubing and cylinder, to allow cylinder articulation.\u003c\/li\u003e\n\u003cli\u003eFor Most Cylinders, add A, B \u0026amp; C + 24”, round up to next even foot. Order that length hose kit, or twice that length in tubing.\u003c\/li\u003e\n\u003cli\u003eHose routings (such as those found on pontoon boats) may vary from this drawing. Confirm length by laying a garden hose along cable path and measure run from wheel to engine connection point.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eTypical Single Station Routing:\u003c\/p\u003e\u003cul\u003e\u003cli\u003eA single, front-mount outboard cylinder system is shown in this diagram.\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eReplacement of Hydraulic Steering:\u003c\/p\u003e\u003cp\u003eIf you removed the old hoses, measure for replacement hoses as follows:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMeasure existing hose from tip to tip, round up to next even foot. Order that length hose kit, or twice that length in tubing.\u003c\/li\u003e\n\u003cli\u003eFrequently Asked Questions\u003c\/li\u003e\n\u003cli\u003eWhat is the SeaStar Outboard Hydraulic Steering Hose Kit used for? The SeaStar Outboard Hydraulic Steering Hose Kit is designed for hydraulic steering systems and includes two hoses with pre-attached hose fittings on both ends. The hoses are kink and abrasion resistant and are designed to exceed SAE and ABYC specifications for precise steering control.\u003c\/li\u003e\n\u003cli\u003eWhich SeaStar hydraulic steering systems are compatible with this hose kit? This hose kit can be used with all SeaStar systems except SeaStar PRO, BayStar, Capilano, and 3-line inboard systems. Verify that your steering system is not one of these excluded applications before purchasing or installing the hoses.\u003c\/li\u003e\n\u003cli\u003eHow do I measure hydraulic hose length for a new installation? Measure the hose routing path from the wheel center line to the engine connection. For most cylinders, add the A, B, and C measurements, then add 24 inches and round up to the next even foot. A garden hose can also be used along the intended routing path to help confirm the required length.\u003c\/li\u003e\n\u003cli\u003eHow much slack should be left when routing the hydraulic steering hoses? Enough slack should be left to prevent sharp bends or kinking because most cylinders move with the engine or rudder. The supplied guidance specifies avoiding bends with a radius of less than 3 inches. When rigid tubing is used, flexible hoses must be installed between the tubing and cylinder to allow cylinder articulation.\u003c\/li\u003e\n\u003cli\u003eHow do I measure replacement hydraulic hoses when the old hoses have been removed? For replacement hoses, measure the existing hose from tip to tip and round the measurement up to the next even foot. Order that length as the hose kit, or twice that length if using tubing.\u003c\/li\u003e\n\u003cli\u003eWhat is included with the SeaStar Outboard Hydraulic Steering Hose Kit? The kit includes two hydraulic steering hoses. Each hose is supplied with pre-attached hose fittings on both ends, so the fittings are already attached to the hoses supplied with the kit.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Teleflex Marine","offers":[{"title":"14'","offer_id":50584277418242,"sku":"TEL-HO5114","price":225.69,"currency_code":"USD","in_stock":true},{"title":"16'","offer_id":50584277451010,"sku":"TEL-HO5116","price":247.39,"currency_code":"USD","in_stock":true},{"title":"18'","offer_id":50584277483778,"sku":"TEL-HO5118","price":267.99,"currency_code":"USD","in_stock":true},{"title":"20'","offer_id":50584277516546,"sku":"TEL-HO5120","price":288.59,"currency_code":"USD","in_stock":true},{"title":"24'","offer_id":50584277549314,"sku":"TEL-HO5124","price":342.29,"currency_code":"USD","in_stock":true},{"title":"26'","offer_id":50584277582082,"sku":"TEL-HO5126","price":405.79,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0842\/3024\/2562\/files\/HO5128__86841.1722362674.jpg?v=1791101653","url":"https:\/\/allmarineworld.com\/products\/seastar-outboard-hydraulic-steering-hose-kit","provider":"All Marine World","version":"1.0","type":"link"}