{"product_id":"pettit-transducer-antifouling-spray-paint","title":"Pettit Paint Transducer Antifoul Spray Aerosol","description":"\u003cp\u003ePettit Transducer Antifouling Spray Paint - 6 oz\u003c\/p\u003e\u003cp\u003ePettit's Transducer Paint is for use only on plastic transducer housings and bare metals including steel, stainless steel, cast iron, copper, bronze, galvanized steel and lead. It forms an excellent adhesive bond to underwater plastic housings and metals, and inhibits corrosion on these surfaces. Transducer Paint's smooth, hard surface will self -clean in service, and can be used above or below the waterline. The dried film of Transducer Paint contains 93% pure zinc.\u003c\/p\u003e\u003cp\u003eSuperior transducer and underwater metal protection\u003c\/p\u003e\u003cp\u003eExcellent adhesion to clean metals and plastic transducer housings\u003c\/p\u003e\u003cp\u003e93% pure zinc in the dried film\u003c\/p\u003e\u003cp\u003eFast dry formula in an easy to use aerosol spray can\u003c\/p\u003e\u003cp\u003eNot for use on aluminum, fiberglass or wood.\u003c\/p\u003e\u003cp\u003eSpecifications:\u003c\/p\u003e\u003cp\u003eSize: 6 oz\u003c\/p\u003e\u003cp\u003eFinish: Flat\u003c\/p\u003e\u003cp\u003eNumber of Coats: 2 or 3\u003c\/p\u003e\u003cp\u003eDo not apply more than three coats as cracking and loss of adhesion may occur if product is applied too thick.\u003c\/p\u003e\u003cp\u003eAssociated Products:\u003c\/p\u003e\u003cul\u003e\u003cli\u003ePettit Brush Thinner: For use during surface preparation\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eHow to Apply\u003c\/p\u003e\u003cp\u003eHOW TO APPLY PETTIT TRANSDUCER ANTIFOULING SPRAY PAINT\u003c\/p\u003e\u003cp\u003eApplication Method: Aerosol Spray\u003c\/p\u003e\u003cp\u003eNumber of Coats: 2 or 3\u003c\/p\u003e\u003cp\u003eNote: Do not apply more than three coats as cracking and loss of adhesion may occur if product is applied too thick or in too many coats.\u003c\/p\u003e\u003cp\u003eApplication Temp: 50°F Minimum | 90°F Maximum\u003c\/p\u003e\u003cp\u003eApplication Humidity:  0% RH Minimum | 85% RH Maximum\u003c\/p\u003e\u003cp\u003eCoverage: 10 sq. ft\/16 oz. spray can\u003c\/p\u003e\u003cp\u003eDRY TIMES:\u003c\/p\u003e\u003cp\u003eTemp\u003c\/p\u003e\u003cp\u003eTo Recoat (Hours)\u003c\/p\u003e\u003cp\u003eTo Launch (Hours)\u003c\/p\u003e\u003cp\u003e90°F\u003c\/p\u003e\u003cp\u003e1\/2\u003c\/p\u003e\u003cp\u003e16\u003c\/p\u003e\u003cp\u003e70°F\u003c\/p\u003e\u003cp\u003e1\u003c\/p\u003e\u003cp\u003e24\u003c\/p\u003e\u003cp\u003e50°F\u003c\/p\u003e\u003cp\u003e2\u003c\/p\u003e\u003cp\u003e48\u003c\/p\u003e\u003cp\u003eSURFACE PREPARATION:\u003c\/p\u003e\u003cul\u003e\u003cli\u003eUnderwater Metals\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eRemove all paint from underwater metals, running gear, and plastic transducer housings by sanding, scraping, sandblasting or by using a paint and varnish remover.\u003c\/p\u003e\u003cp\u003eNote: Do not use any solvent or paint and varnish remover containing ketone type solvents such as acetone, methylethyl ketone or methyl isobutyl ketone as these solvents will destroy the plastic transducer housing.\u003c\/p\u003e\u003cp\u003eOnce back to bare, clean metal, wipe the surface with Pettit 120 Brushing Thinner and let dry.\u003c\/p\u003e\u003cp\u003eMetals above Water\u003c\/p\u003e\u003cp\u003eRemove all paint and rust with a wire brush or sandpaper. Lightly sand glossy surfaces.\u003c\/p\u003e\u003cp\u003eClean surface with Pettit 120 Brushing Thinner and let dry.\u003c\/p\u003e\u003cp\u003eAPPLICATION:\u003c\/p\u003e\u003cp\u003eShake can vigorously for two minutes after the mixing balls begin to rattle.\u003c\/p\u003e\u003cp\u003eShake often during use\u003c\/p\u003e\u003cp\u003eHold can upright 12 to 16 inches from the surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Be sure to keep the can the same distance from the surface and in motion while spraying.\u003c\/p\u003e\u003cp\u003eNote: Allow no more than 5 minutes between two or three thin coats. Otherwise, allow to dry one hour before applying additional coats.\u003c\/p\u003e\u003cp\u003eWhen finished spraying, clear spray valve by turning can upside down and spraying until no more paint comes out. If valve clogs, twist and pull off spray tip and rinse it in a solvent such as mineral spirits.\u003c\/p\u003e\u003cp\u003eDo not stick a pin or other object in the stem\u003c\/p\u003e\u003cp\u003eInformation sourced from Pettit Tranducer Paint 1793 Technical Bulletin 159\u003c\/p\u003e\u003cp\u003eHow to Apply\u003c\/p\u003e","brand":"Pettit Paint","offers":[{"title":"Default Title","offer_id":50581927166210,"sku":"PET-1793","price":36.89,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0842\/3024\/2562\/files\/1793__97652.1739459121_8793a59e-0aa4-474a-bb5a-dd9bc8387266.jpg?v=1791079954","url":"https:\/\/allmarineworld.com\/products\/pettit-transducer-antifouling-spray-paint","provider":"All Marine World","version":"1.0","type":"link"}