{"product_id":"pettit-ez-decks-non-skid-paint","title":"Pettit Paint Ez-Decks White Qt","description":"\u003cp\u003ePettit EZ Decks Non Skid Deck Paint\u003c\/p\u003e\u003cp\u003eThe state-of-the-art Pettit EZ Decks non-skid deck paint adds a powerful finish that the weather simply can’t penetrate. It stays durable for years and is very simple to apply. Part of its secret lies within its special grit that produces a durable, slip-resistant finish applicable to all decks and cabin soles. As with other select Pettit “EZ” products, Pettit EZ Decks allows for a seamless way to achieve maximum results with little-to-no effort.\u003c\/p\u003e\u003cp\u003eThe durable weather-resistant finish helps to prevent long term abrasions and abuse. Comes loaded with ultraviolet filters to combat fading while offering premium color retention that will stay vibrant for years without cracking like lesser deck finishes. Available in three popular colors that match perfectly with Pettit’s Easypoxy topside enamel.\u003c\/p\u003e\u003cp\u003eFeatures:\u003c\/p\u003e\u003cp\u003eProvides a super tough non-skid finish\u003c\/p\u003e\u003cp\u003eExtremely durable weather-resistant finish\u003c\/p\u003e\u003cp\u003eFade and UV resistant, colors hold up under tough conditions\u003c\/p\u003e\u003cp\u003eEZ decks is simple to use and easy to apply\u003c\/p\u003e\u003cp\u003eSold in Quarts\u003c\/p\u003e\u003cp\u003eAssociated Products:\u003c\/p\u003e\u003cp\u003ePettit Brush Thinner - For brushing and clean up\u003c\/p\u003e\u003cp\u003ePettit Spray Thinner -For spraying application\u003c\/p\u003e\u003cp\u003ePettit Bio-Blue - For preparing bare fiberglass surface\u003c\/p\u003e\u003cp\u003eSpecifications:\u003c\/p\u003e\u003cp\u003eFinish: High Gloss\u003c\/p\u003e\u003cp\u003eCoverage: 600 sq. ft\/gal.\u003c\/p\u003e\u003cp\u003eNumber of Coats: 2 Minimum\u003c\/p\u003e\u003cp\u003eHow To Apply Pettit EZ Decks Non-Skid Paint\u003c\/p\u003e\u003cp\u003eStir EZ Decks thoroughly before use, as the non-skid agent in the paint will float to the surface in the container. This paint can be applied by brush or roller; if applying by brush or roller, apply without thinning. If applying in hot weather, 5-10% of Pettit 120 Thinner may be added to maintain a wet edge. For best results on large surfaces, roll out using a short nap or foam roller followed immediately by leveling off with the tip of a brush.\u003c\/p\u003e\u003cp\u003eApplication Method: Brush or roller\u003c\/p\u003e\u003cp\u003eNumber of Coats: 2 minimum\u003c\/p\u003e\u003cp\u003eDry Film Thickness per Coat: 1.5 mils (2.6 wet mils)\u003c\/p\u003e\u003cp\u003eCoverage: 600 sq. ft\/gal.\u003c\/p\u003e\u003cp\u003eApplication Temp: 50°F Min. \/ 90°F Max.\u003c\/p\u003e\u003cp\u003eThinner: 120 Brushing Thinner (clean up also)\u003c\/p\u003e\u003cp\u003eDRY TIMES:\u003c\/p\u003e\u003cp\u003eTemp\u003c\/p\u003e\u003cp\u003eTo Touch\u003c\/p\u003e\u003cp\u003eTo Recoat\u003c\/p\u003e\u003cp\u003e90°F\u003c\/p\u003e\u003cp\u003e1-1\/2 Hours\u003c\/p\u003e\u003cp\u003e8 Hours\u003c\/p\u003e\u003cp\u003e70°F\u003c\/p\u003e\u003cp\u003e3 Hours\u003c\/p\u003e\u003cp\u003e16 Hours\u003c\/p\u003e\u003cp\u003e50°F\u003c\/p\u003e\u003cp\u003e6 Hours\u003c\/p\u003e\u003cp\u003e24 Hours\u003c\/p\u003e\u003cp\u003eApplication Systems\u003c\/p\u003e\u003cp\u003eBare Wood\u003c\/p\u003e\u003cp\u003eSand surface smooth with 80-120 grit sandpaper, then solvent clean with Pettit 120 Thinner to remove residue.\u003c\/p\u003e\u003cp\u003eFill all screw heads or small holes with an epoxy fairing compound; sand flush and solvent clean.\u003c\/p\u003e\u003cp\u003eApply a coat of 2018 Clear Sealer to penetrate and seal the porous grain.\u003c\/p\u003e\u003cp\u003eFollow with one or  two coats of 6149 Easypoxy White Undercoater until an evenly smooth base condition is reached.\u003c\/p\u003e\u003cp\u003eSand each coat with 80-120 grit sandpaper and solvent clean with Pettit 120 Thinner.\u003c\/p\u003e\u003cp\u003eProceed with the first finish coat of EZ Decks.\u003c\/p\u003e\u003cp\u003eBare Steel\u003c\/p\u003e\u003cp\u003eSurface must be cleaned to a bright finish by sandblasting or grinding. Remove blast residue.\u003c\/p\u003e\u003cp\u003eImmediately apply one coat of 6980 Rustlok Primer. Allow to dry until tacky.\u003c\/p\u003e\u003cp\u003eIf surface is rough, apply a coat of 6627 Tie-Coat Primer. Sand well and solvent clean.\u003c\/p\u003e\u003cp\u003eRepeat application as needed until a smooth, uniform base is reached.\u003c\/p\u003e\u003cp\u003eProceed with the first coat of EZ Decks.\u003c\/p\u003e\u003cp\u003eBare Aluminum\u003c\/p\u003e\u003cp\u003eWipe the surface free of oil and grease with Pettit 120 Thinner.\u003c\/p\u003e\u003cp\u003eRemove oxidation and etch the surface with medium grit emery cloth. Remove sanding residue.\u003c\/p\u003e\u003cp\u003eApply one thin \"wet\" coat of 6455\/044 Metal Primer. Allow to dry at least two hours.\u003c\/p\u003e\u003cp\u003eProceed with the first coat of EZ Decks.\u003c\/p\u003e\u003cp\u003e6149 Easypoxy White Undercoater can be used over the 6455\/044 Metal Primer for smoothing surfaces if desired.\u003c\/p\u003e\u003cp\u003eBare Fiberglass\u003c\/p\u003e\u003cp\u003eThe entire surface being painted must be thoroughly washed with 120 Thinner or 92 Bio-Blue.\u003c\/p\u003e\u003cp\u003eSand the gel coat with 80 to 120 grit sandpaper to a dull, frosty appearance. Solvent clean to remove residue.\u003c\/p\u003e\u003cp\u003eIf the surface is in excellent condition, proceed with the fi…\u003c\/p\u003e","brand":"Pettit Paint","offers":[{"title":"Default Title","offer_id":50581929722114,"sku":"PET-3127Q","price":74.69,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0842\/3024\/2562\/files\/Pettit_EZ_Decks_Non_Skid_photo__51022.1753840705_2e67a95f-1747-4b46-96b2-ac9e15246dc1.webp?v=1791079972","url":"https:\/\/allmarineworld.com\/products\/pettit-ez-decks-non-skid-paint","provider":"All Marine World","version":"1.0","type":"link"}