{"product_id":"pettit-ez-bilge-quart","title":"Pettit Paint EZ Bilge Quart","description":"\u003cp\u003ePettit EZ Bilge Performance Bilge Paint\u003c\/p\u003e\u003cp\u003ePettit's EZ Bilge is a durable high-performance alkyd finish specially formulated to withstand the abuses associated with boat bilges. The hardwearing finish is resistant to antifreeze, grease, gasoline, diesel fuel, and engine oil. Its tough resilient surface will stand up to years of abrasion and wear. EZ-Bilge utilizes a high-solids formula that is easy to apply by brush, roller or spray and provides excellent coverage. Like other Pettit \"EZ\" products, EZ-Bilge provides the simplest way to achieve optimum results with minimum effort.\u003c\/p\u003e\u003cp\u003eFeatures:\u003c\/p\u003e\u003cp\u003eHigh-performance coating specially designed for boat bilges\u003c\/p\u003e\u003cp\u003eSuper tough finish is fuel, oil, and abrasion resistant\u003c\/p\u003e\u003cp\u003eHigh covering formula is easy to apply\u003c\/p\u003e\u003cp\u003eSuperior protection that withstands tough bilge conditions\u003c\/p\u003e\u003cp\u003eSpecifications:\u003c\/p\u003e\u003cp\u003eType: Oil modified alkyd\u003c\/p\u003e\u003cp\u003eFinish: High-gloss\u003c\/p\u003e\u003cp\u003eRecommended Usage: Bilges\u003c\/p\u003e\u003cp\u003eColors Available: 3124 White, 3125 Gray\u003c\/p\u003e\u003cp\u003eCoverage: 545 sq. ft\/gal.\u003c\/p\u003e\u003cp\u003eNumber of Coats: 2 minimum\u003c\/p\u003e\u003cp\u003eVOC: 388 grams\/liter (max)\u003c\/p\u003e\u003cp\u003eAssociated Products\u003c\/p\u003e\u003cp\u003ePettit Brush Thinner -For brushing and clean up\u003c\/p\u003e\u003cp\u003ePettit Spray Thinner -Spraying Application\u003c\/p\u003e\u003cp\u003ePettit Bio-Blue - Surface cleaning for bare fiberglass and painted surfaces\u003c\/p\u003e\u003cp\u003eHow to Apply Pettit EZ Bilge Paint\u003c\/p\u003e\u003cp\u003ePettit EZ Bilge is a hard-wearing finish that can be applied to properly prepared fiberglass, metal, wood, and over existing metals. The surface must be free of dirt, loose paint, rust, oil, grease, wax, soap, and any other foreign matter. Stir thoroughly before use. EZ Bilge may be applied by brush, roller, conventional or airless spray. For brush or roller application apply without thinning although in hot weather 5 to 10% Pettit #120 Brushing Thinner may be added to maintain a wet edge. For best results on large, smooth surfaces roll out using a short nap roller followed immediately by leveling off with the tip of a brush. For conventional spray application thin 15 to 20% with Pettit 121 Spraying Thinner.\u003c\/p\u003e\u003cp\u003eApplication Methods: Brush, Roller, or Spray\u003c\/p\u003e\u003cp\u003eNumber of Coats: 2 minimum\u003c\/p\u003e\u003cp\u003eDry Film Thickness: 1.5 mils (3 wet mils)\u003c\/p\u003e\u003cp\u003eCoverage: 545 sq. ft\/gal.\u003c\/p\u003e\u003cp\u003eApplication Temp: 50°F Min. \/ 90°F Max.\u003c\/p\u003e\u003cp\u003eThinner: 120 Brushing Thinner or 121 Spraying Thinner\u003c\/p\u003e\u003cp\u003eDRY TIMES:\u003c\/p\u003e\u003cp\u003eTemp\u003c\/p\u003e\u003cp\u003eTo Touch\u003c\/p\u003e\u003cp\u003eTo Recoat\u003c\/p\u003e\u003cp\u003e90°F\u003c\/p\u003e\u003cp\u003e1-1\/2 HR\u003c\/p\u003e\u003cp\u003e8 HR\u003c\/p\u003e\u003cp\u003e70°F\u003c\/p\u003e\u003cp\u003e3 HR\u003c\/p\u003e\u003cp\u003e16 HR\u003c\/p\u003e\u003cp\u003e50°F\u003c\/p\u003e\u003cp\u003e6 HR\u003c\/p\u003e\u003cp\u003e24 HR\u003c\/p\u003e\u003cp\u003eApplication Systems\u003c\/p\u003e\u003cp\u003ePainted Surfaces\u003c\/p\u003e\u003cp\u003eClean painted areas by washing with a solution of two cups household ammonia per gallon of water. Rinse well.\u003c\/p\u003e\u003cp\u003eIf the old paint is an oil-based enamel or polyurethane, and is in good condition, sand with 150 grit sand paper.\u003c\/p\u003e\u003cp\u003eSolvent clean then apply first coat of EZ Bilge.\u003c\/p\u003e\u003cp\u003eIf the old oil-based or polyurethane paint contained a non-skid material, scrub the non-skid surface with Pettit 92 Bio-Blue using a stuff bristle brush.\u003c\/p\u003e\u003cp\u003eRinse thoroughly and allow surface to dry. Then apply two coats of EZ Bilge.\u003c\/p\u003e\u003cp\u003eIf the old paint is latex or water-based, or is in poor condition, remove it with a paint or varnish remover or by sanding.\u003c\/p\u003e\u003cp\u003eProceed with the instructions for the appropriate bare surface system.\u003c\/p\u003e\u003cp\u003eBare Wood\u003c\/p\u003e\u003cp\u003eSand surface smooth with 80-120 grit sandpaper.\u003c\/p\u003e\u003cp\u003eSolvent clean with Pettit 120 Brushing Thinner.\u003c\/p\u003e\u003cp\u003eApply coat of 2018 EZ Wood Sealer.\u003c\/p\u003e\u003cp\u003eFollow with one or two coats of 6149 EZ Prime until an evenly smooth base condition is reached.\u003c\/p\u003e\u003cp\u003eSand each coat with 80-120 grit sandpaper and solvent clean with Pettit 120 Brushing Thinner.\u003c\/p\u003e\u003cp\u003eProceed with the first coat of EZ Bilge.\u003c\/p\u003e\u003cp\u003eBare Steel\u003c\/p\u003e\u003cp\u003eSurface must be cleaned to a bright finish.\u003c\/p\u003e\u003cp\u003eImmediately apply one coat of 6980 Rustlok Primer. Allow to dry until tacky.\u003c\/p\u003e\u003cp\u003eIf surface is rough, apply a coat of 6627 Tie-Coat Primer. Sand well and solvent clean.\u003c\/p\u003e\u003cp\u003eRepeat application of Tie-Coat Primer as needed until a smooth base is achieved.\u003c\/p\u003e\u003cp\u003eProceed with the first coat of EZ Bilge.\u003c\/p\u003e\u003cp\u003eBare Alum…\u003c\/p\u003e","brand":"Pettit Paint","offers":[{"title":"Gray","offer_id":50581929623810,"sku":"PET-3125Q","price":59.29,"currency_code":"USD","in_stock":false},{"title":"White","offer_id":50581929656578,"sku":"PET-3124Q","price":59.29,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0842\/3024\/2562\/files\/428918_source_1752000525_33e30e17-783d-4e04-985a-47e069c01a61.jpg?v=1791079971","url":"https:\/\/allmarineworld.com\/products\/pettit-ez-bilge-quart","provider":"All Marine World","version":"1.0","type":"link"}