{"product_id":"pettit-copper-bronze-antifouling-bottom-paint","title":"Pettit Paint Copper Bronze Antifouling Bottom Paint","description":"\u003cp\u003ePettit Copper Bronze Antifouling Bottom Paint\u003c\/p\u003e\u003cp\u003eCopper Bronze is an excellent, general purpose antifouling for boaters desiring aggressive bottom protection in an easy to apply, cosmetically attractive finish. Copper Bronze antifouling is resistant to algae, barnacles, grass, zebra mussels, etc. Copper Bronze antifouling is equally effective in both fresh and saltwater and is also ideal for trailered boats.\u003c\/p\u003e\u003cp\u003eFeatures:\u003c\/p\u003e\u003cp\u003eCuprous Oxide for aggressive antifouling protection\u003c\/p\u003e\u003cp\u003eHard, modified epoxy finish withstands season-long use and abuse\u003c\/p\u003e\u003cp\u003eCompatible with most previously applied bottom paints\u003c\/p\u003e\u003cp\u003eSuitable for use on fiberglass, wood and steel hulls\u003c\/p\u003e\u003cp\u003eExcellent protection for trailered boats\u003c\/p\u003e\u003cp\u003eSpecifications:\u003c\/p\u003e\u003cp\u003eFinish: Flat\u003c\/p\u003e\u003cp\u003eCoverage: 400 sq. ft\/gal.\u003c\/p\u003e\u003cp\u003eNumber of Coats: 2\u003c\/p\u003e\u003cp\u003eHow To Apply\u003c\/p\u003e\u003cp\u003eAPPLICATION DATA METHOD: Brush, Roller, Airless or Conventional Spray\u003c\/p\u003e\u003cp\u003eNUMBER OF COATS: 2\u003c\/p\u003e\u003cp\u003eDRY FILM THICKNESS PER COAT: 2 mils (4.1 wet mils)\u003c\/p\u003e\u003cp\u003eCOVERAGE: 400 sq. ft\/gal.\u003c\/p\u003e\u003cp\u003eAPPLICATION TEMP: 40°F Min. \/ 90°F Max.\u003c\/p\u003e\u003cp\u003eTHINNER: 120 Brushing, 121 Spraying\u003c\/p\u003e\u003cp\u003eDRY TIMES:\u003c\/p\u003e\u003cp\u003eTemp\u003c\/p\u003e\u003cp\u003eTo Recoat\u003c\/p\u003e\u003cp\u003eTo Launch\u003c\/p\u003e\u003cp\u003e90°F\u003c\/p\u003e\u003cp\u003e2 HR\u003c\/p\u003e\u003cp\u003e8 HR\u003c\/p\u003e\u003cp\u003e70°F\u003c\/p\u003e\u003cp\u003e4 HR\u003c\/p\u003e\u003cp\u003e16 HR\u003c\/p\u003e\u003cp\u003e50°F\u003c\/p\u003e\u003cp\u003e6 HR\u003c\/p\u003e\u003cp\u003e24 HR\u003c\/p\u003e\u003cp\u003ePREVIOUSLY PAINTED SURFACES: If the previous coating is in good condition, thoroughly sand with 80 grit paper then solvent clean with 120 Brushing Thinner to remove residue. Apply two fi nish coats of Copper Bronze. If the previous coating is soft or in poor condition, remove to the bare surface by sanding or using Pettit 9051 Bio Blast Paint Remover. Proceed with appropriate bare system as described below. Old tin copolymers should be removed or sealed with Pettit 6627 Tie Coat Primer before applying Copper Bronze.\u003c\/p\u003e\u003cp\u003eBARE FIBERGLASS: All bare fi berglass, regardless of age, should be thoroughly cleaned several times with Pettit 95 Fiberglass Dewaxer or 120 Brushing Thinner. Sand thoroughly with 80 grit sandpaper to a dull, frosty fi nish and rewash the sanded surface with 95 Fiberglass Dewaxer or 120 Brushing Thinner to remove sanding residue. Then apply two coats of Copper Bronze, following application instructions. Careful observation of the above instructions will help ensure long term adhesion of this and subsequent years’ antifouling paint.\u003c\/p\u003e\u003cp\u003eBARE WOOD: Sand entire surface with 80 grit paper; wash clean with 120 Brushing Thinner. Apply a coat of Copper Bronze thinned 25% with 120 Brushing Thinner, allow an overnight dry, lightly sand and wipe clean. Apply two fi nish coats of Copper Bronze.\u003c\/p\u003e\u003cp\u003eSTEEL HULLS: Sandblast or disc sand to a clean, bright fi nish and remove residue. Then either immediately apply two coats of 6980 Rustlok Steel Primer, allowing each to dry only 1-2 hours prior to overcoating - OR - immediately apply one thin coat of 6455 Metal Primer and allow to dry two hours; follow with two coats of 6627 Tie Coat Primer, allowing each to dry two hours minimum. Apply two fi nish coats of Copper Bronze.\u003c\/p\u003e\u003cp\u003eKEELS - LEAD: Abrade surface to bright metal; clean off residue. Apply one thin coat of 6455\/044 Metal Primer; allow to dry two hours. Apply one coat of Pettit 6627 Tie Coat Primer then, if fairing is required, apply Epoxy Fairing Compound. Follow with an additional coat of 6627 Tie Coat Primer per label directions. Apply two fi nish coats of Copper Bronze.\u003c\/p\u003e\u003cp\u003eKEELS - STEEL OR CAST IRON: Abrade surface to bright metal; clean off residue. Apply one coat of 6980 Rustlok Steel Primer, allowing to dry only 1 - 2 hours prior to overcoating. Then, if fairing is required, apply Epoxy Fairing Compound followed by two coats of Pettit 6627 Tie Coat Primer, fi nish with two fi nish coats of Copper Bronze.\u003c\/p\u003e\u003cp\u003eDO NOT USE THIS PRODUCT ON ALUMINUM HULLS AND OUTDRIVES.\u003c\/p\u003e\u003cp\u003eAPPLICATION INFORMATION: Copper Bronze is loaded with cuprous oxide. As a result of this there is a tendency for settling to occur, especially if the paint has been on the shelf for several months. It is necessary to thoroughly mix the paint before using. If possible shak…\u003c\/p\u003e","brand":"Pettit Paint","offers":[{"title":"Default Title","offer_id":50581927395586,"sku":"PET-1933G","price":488.39,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0842\/3024\/2562\/files\/383067_source_1751905491_5ea01728-1e3a-4c26-83e8-608187ccbc68.jpg?v=1791079957","url":"https:\/\/allmarineworld.com\/products\/pettit-copper-bronze-antifouling-bottom-paint","provider":"All Marine World","version":"1.0","type":"link"}