{"product_id":"pettit-alumaprotect-epoxy-barrier-coat-primer","title":"Pettit Paint AlumaProtect Epoxy Barrier Coat Primer","description":"\u003cp\u003ePettit Aluma Protect Epoxy Barrier Coat Marine Primer For Aluminum Hulls\u003c\/p\u003e\u003cp\u003eAluma Protect is a 2 part strontium chromate primer designed to form the ideal barrier coat over roughed bare aluminum. This is the appropriate epoxy to use when aluminum has been sandblasted, sanded or ground so that a tooth is present. For smooth aluminum, choose Pettit Metal Primer.\u003c\/p\u003e\u003cp\u003eAlumaProtect provides maximum resistance to fresh or salt water, thus eliminating corrosion. This complete coating system resists water, industrial chemical fumes, and very humid environments. Intended to be used as a primary coat over bare aluminum hulls and outdrives. AlumaProtect 4400\/4401 will chalk if not topcoated. Two coats are recommended over sandblasted aluminum. Then overcoat with Pettit Protect for optimum results before finishing antifouling paint.\u003c\/p\u003e\u003cp\u003eEpoxy Primer for Aluminum\u003c\/p\u003e\u003cp\u003eStrontium Chromate for Maximum Corrosion Control\u003c\/p\u003e\u003cp\u003eEasy to Apply and Excellent Bonding Surface\u003c\/p\u003e\u003cp\u003eSmooth Finish\u003c\/p\u003e\u003cp\u003ePettit Epoxy Thinner: Thinning is not usually needed, but for slow drying in hot weather or windy conditions, small amounts may be added. Do not add more than 10% by volume.\u003c\/p\u003e\u003cp\u003eSpecifications:\u003c\/p\u003e\u003cp\u003eFinish: Low Luster\u003c\/p\u003e\u003cp\u003eColor: Bright yellow\u003c\/p\u003e\u003cp\u003eCoverage: 800 sq. ft\/2 gal. kit\u003c\/p\u003e\u003cp\u003eNumber of Coats: 1 or more\u003c\/p\u003e\u003cp\u003eHow To Apply\u003c\/p\u003e\u003cp\u003eAPPLICATION DATA METHOD: Brush, Roller, Airless or Conventional Spray\u003c\/p\u003e\u003cp\u003eNUMBER OF COATS: 1 or more\u003c\/p\u003e\u003cp\u003eDRY FILM THICKNESS PER COAT:  1 mils (3.6 wet mils)\u003c\/p\u003e\u003cp\u003eCOVERAGE: 450 sq. ft\/gal.\u003c\/p\u003e\u003cp\u003eAPPLICATION TEMP: 50°F Min. \/ 90°F Max.\u003c\/p\u003e\u003cp\u003eTHINNER: 97 Epoxy Thinner\u003c\/p\u003e\u003cp\u003eDRY TIMES:\u003c\/p\u003e\u003cp\u003eTemp\u003c\/p\u003e\u003cp\u003eTo Recoat\u003c\/p\u003e\u003cp\u003eTo Launch\u003c\/p\u003e\u003cp\u003eTo Bottom Paint\u003c\/p\u003e\u003cp\u003e90°F\u003c\/p\u003e\u003cp\u003e1-24 HR\u003c\/p\u003e\u003cp\u003e48 HR\u003c\/p\u003e\u003cp\u003e1-8 HR\u003c\/p\u003e\u003cp\u003e70°F\u003c\/p\u003e\u003cp\u003e4-96 HR\u003c\/p\u003e\u003cp\u003e72 HR\u003c\/p\u003e\u003cp\u003e4-16 HR\u003c\/p\u003e\u003cp\u003e50°F\u003c\/p\u003e\u003cp\u003e8-192 HR\u003c\/p\u003e\u003cp\u003e120 HR\u003c\/p\u003e\u003cp\u003e120 HR\u003c\/p\u003e\u003cp\u003e*If these recommended intervals are exceeded, sand thoroughly with 80 grit sandpaper before recoating or applying bottom paint.\u003c\/p\u003e\u003cp\u003ePREVIOUSLY PAINTED SURFACES: Aluma Protect Aluminum Epoxy Primer 4400\/4401 may be applied over existing two part epoxy fi nishes, provided they are in sound condition. Brush-off sandblasting or very heavy sanding with 60 grit sandpaper is required to maintain maximum adhesion. Then apply one or two coats 4400\/4401 per instructions. Remember, coating performance is only as good as the surface to which it’s applied. All existing two package epoxy fi nishes in poor condition, as well as all one package primers and bottom paints, should be removed completely and the appropriate bare aluminum system as described above should be followed before using Aluma Protect Aluminum Epoxy Primer 4400\/4401. Aluma Protect Aluminum Epoxy Primer is not recommended for use over antifouling paints.\u003c\/p\u003e\u003cp\u003eSTEEL HULLS: Not recommended - use Pettit Protect 4700\/4701 for steel surfaces.\u003c\/p\u003e\u003cp\u003eALUMINUM: Sandblast (using non-metallic media) or disc sand the aluminum to clean, bright metal. Wipe clean of residue and immediately apply one coat of Aluma Protect Aluminum Epoxy Primer 4400\/4401. At 70°F let dry 4 hours minimum, 96 hours maximum, and apply an additional coat followed by two coats of Pettit Protect High Build Epoxy Primer 4700\/4701 following application and recoat instructions.\u003c\/p\u003e\u003cp\u003eAPPLICATION INFORMATION: Stir both components thoroughly. Mix the two components together in the ratio of 1 part of Component A to 1 part of Component B by volume. Allow to stand 15 minutes at approximately 70° before using. (Allow to stand at least 30 minutes if temperature is between 50° and 65°F) May be applied by brush, roller, conventional or airless spray. Thinning is not normally required for application, however, small amounts of 97 Epoxy Thinner may be used if necessary to facilitate application. Wet fi lm thickness should be 3.6 mils per coat, which yields 1.0 mil dry fi lm thickness. A wet fi lm thickness gauge should be used to monitor paint application. One or two coats of Aluma Protect 4400\/4401 should be overcoated with Pettit Protect 4700\/4701 to provide a corrosion and chemical resist…\u003c\/p\u003e","brand":"Pettit Paint","offers":[{"title":"Default Title","offer_id":50581929984258,"sku":"PET-4400-4401G","price":438.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0842\/3024\/2562\/files\/382625_source_1647351681.jpg?v=1791079975","url":"https:\/\/allmarineworld.com\/products\/pettit-alumaprotect-epoxy-barrier-coat-primer","provider":"All Marine World","version":"1.0","type":"link"}