{"product_id":"interlux-vc-performance-epoxy-bottom-finish","title":"Interlux Paint Vc Performance Epoxy 2-Part Kit","description":"\u003cp\u003eInterlux VC Performance Epoxy Boat Bottom Paint\u003c\/p\u003e\u003cp\u003eSold as kit Makes 2 Gallons.\u003c\/p\u003e\u003cp\u003eVC Performance is a fluoro microadditive bearing two-part epoxy for use on the underwater surfaces of high performance boats. Apply to gelcoat, bare fiberglass, epoxy and primed metal surfaces. Dries to a hard, somewhat slippery, semi-gloss white finish that is ideal for wet sanding and burnishing. The hard, stain-resistant finish is also ideal for rack-stored and trailered boats or boats that are kept in the water (not requiring antifouling properties). VC Performance has no antifouling or foul release properties.\u003c\/p\u003e\u003cp\u003eSpecifications:\u003c\/p\u003e\u003cp\u003eFinish: Semi-gloss\u003c\/p\u003e\u003cp\u003eMix Ratio: 1 : 1 by volume\u003c\/p\u003e\u003cp\u003eNumber of Coats: 3-4 as needed\u003c\/p\u003e\u003cp\u003eCoverage: 199.9 ft²\/gal by spray\u003c\/p\u003e\u003cp\u003eInterlux Reducing Solvent: Thinner; thin, if necessary, after induction\u003c\/p\u003e\u003cp\u003e*****WILL SHIP TO CONTINENTAL 48 STATES GROUND ONLY****\u003c\/p\u003e\u003cp\u003eHow To Apply\u003c\/p\u003e\u003cp\u003eAPPLICATION DATA METHOD: Airless Spray, Brush, Conventional Spray, Roller- Pressure Pot or Siphon Cup\u003c\/p\u003e\u003cp\u003eNUMBER OF COATS: 3-4\u003c\/p\u003e\u003cp\u003eDRY FILM THICKNESS PER COAT: 3.6 mils\u003c\/p\u003e\u003cp\u003eCOVERAGE: 200 sq. ft\/gal.\u003c\/p\u003e\u003cp\u003eAPPLICATION TEMP: 50°F Min. \/ 95°F Max.\u003c\/p\u003e\u003cp\u003eTHINNER: Reducing Solvent 2316N\u003c\/p\u003e\u003cp\u003eDRY TIMES:\u003c\/p\u003e\u003cp\u003eTemp\u003c\/p\u003e\u003cp\u003eTo Touch\u003c\/p\u003e\u003cp\u003eTo Recoat\u003c\/p\u003e\u003cp\u003ePot Life\u003c\/p\u003e\u003cp\u003eTo Launch\u003c\/p\u003e\u003cp\u003e95°F\u003c\/p\u003e\u003cp\u003e2 HR\u003c\/p\u003e\u003cp\u003e4 HR\u003c\/p\u003e\u003cp\u003e4 HR\u003c\/p\u003e\u003cp\u003e3 DAY\u003c\/p\u003e\u003cp\u003e73°F\u003c\/p\u003e\u003cp\u003e2 HR\u003c\/p\u003e\u003cp\u003e5 HR\u003c\/p\u003e\u003cp\u003e5 HR\u003c\/p\u003e\u003cp\u003e4 DAY\u003c\/p\u003e\u003cp\u003e50°F\u003c\/p\u003e\u003cp\u003e3 HR\u003c\/p\u003e\u003cp\u003e6 HR\u003c\/p\u003e\u003cp\u003e6 HR\u003c\/p\u003e\u003cp\u003e7 DAY\u003c\/p\u003e\u003cp\u003eNote: Maximum Immersion Times are as follows: 10-35°C\/50-95°F - 60 days\u003c\/p\u003e\u003cp\u003eBARE FIBERGLASS: Begin by scrubbing well using soap and water and a stiff brush. Rinse with fresh water. Wipe with Fiberglass Solvent Wash 202. Sand with 80 grade (grit) paper. Wipe with Fiberglass Solvent Wash 202.\u003c\/p\u003e\u003cp\u003eBARE METAL: Sandblast or grind to bright metal finish. Immediately apply Viny-Lux Primewash 353\/354 thinned 25% with Viny-Lux Solvent 355. Allow to dry for 1-24 hours.\u003c\/p\u003e\u003cp\u003eCLEAR EPOXY: Begin by scrubbing well using soap and water and a stiff brush. Rinse with fresh water. Wet sand with 80 grade (grit) paper. Wash down with fresh water. Wipe with Fiberglass Solvent Wash 202.\u003c\/p\u003e\u003cp\u003eAPPLICATION INFORMATION: Apply 3 coats of VC Performance Epoxy. VC Performance Epoxy is designed for spray application but can be applied by brush and rollers. Mix base and curing agent thoroughly at the specified ratio. Allow 45 mins at 50°F\/10°C and 30 mins above 77° F\/25°C for induction. Thin, if necessary, after induction. Airless Spray Pressure: 142-170 bar\/2100-2500 psi Tip Size: 0.48-0.53 mm\/19-21 thou. Conventional Spray Pressure Pot: Pressure: 3.44-4.08 bar\/50-60 psi - gun pressure; 8-15 psi pot pressure. Tip Size: 1.4-1.5 mm\/55-60 thou. Siphon Cup: Pressure: 3.06-4.08 bar\/45-60 psi. Tip Size: 1.4-1.5 mm\/55-60 thou. Other If fairing is necessary, use Interprotect Watertite between 1st and 2nd coats of VC Performance Epoxy and then apply 3 coats of VC Performance Epoxy over the Interprotect Watertite. VC Performance Epoxy can be applied to gelcoat, bare fiberglass, epoxy and properly primed metal. Apply to clean, dry, properly prepared surfaces only. VC Performance Epoxy can only be applied over two component products that are specified for underwater use. If there is any single paint (such as antifouling paint) on the surface, it must be removed and then proceed as with bare surface.\u003c\/p\u003e\u003cp\u003eMSDS\u003c\/p\u003e\u003cp\u003eClick here to download VC Performance Epoxy Bottom Finish Datasheet\u003c\/p\u003e\u003cp\u003eFrequently Asked Questions\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eWhat is Interlux VC Performance Epoxy designed for? Interlux VC Performance Epoxy is a two-part epoxy bottom finish designed for high performance boats. It creates a hard, smooth, semi-gloss surface that is ideal for wet sanding and burnishing to help reduce drag.\u003c\/li\u003e\n\u003cli\u003eDoes Interlux VC Performance Epoxy provide antifouling protection? No. Interlux VC Performance Epoxy does not have antifouling or foul release properties. It is intended for boats that do not require antifouling protection.\u003c\/li\u003e\n\u003cli\u003eWhat surfaces can Interlux VC Performance Epoxy be applied to? Interlux VC P…\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Interlux Paint","offers":[{"title":"Default Title","offer_id":50581708210434,"sku":"ILX-V127KITG","price":303.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0842\/3024\/2562\/files\/ilx-v127kitg_lg__23813.1722361287.webp?v=1791078378","url":"https:\/\/allmarineworld.com\/products\/interlux-vc-performance-epoxy-bottom-finish","provider":"All Marine World","version":"1.0","type":"link"}