{"product_id":"gluvit-epoxy-waterproof-sealer","title":"ITW Marine Tex Gluvit Epoxy Sealer 2# Amber Color","description":"\u003cp\u003eGluvit Waterproof Epoxy Sealer -RM330K  - Quart 2 lbs.\u003c\/p\u003e\u003cp\u003eProtecting your hulls and decks has never been easier with Gluvit Waterproof Epoxy Sealer. Made to protect fiberglass wood, aluminum, and steel it provides an extra barrier and protective coating. Wear and tear on boats can cause cracks, pinholes, and leaky seams, Gluvit waterproof sealer can bridge and seal cracks and fill in minor pinholes. Its long lasting life allows it to penetrate into cracks for added strength. The sealer helps to minimize corrosion and water absorption.\u003c\/p\u003e\u003cp\u003eDeteriorated wood on decks and hulls can be brought back to life with Gluvit Waterproof Epoxy Sealer. Applying sealer protects planks and sheeting from water damage and marine parasites. Minimize galvaniccorrosion and seal rivets on aluminum hulls with this waterproof sealer and protect jet skis, and other fiberglass boats from the abrasive beaches and rocks and prevents blistering and corrosion.\u003c\/p\u003e\u003cp\u003eIn order to maximize protection with Gluvit sealer it must be painted after it has cured. This will provide maximum UV protection. Once ready to paint, lightly sand where sealer was applied. Then paint with any pigmented epoxy, urethane, latex or alkyd based paint. Gluvit Epoxy Waterproof Sealer is available in quart which covers 25-35 square feet or gallon size which covers 100-130 square feet.\u003c\/p\u003e\u003cp\u003eSpecifications:\u003c\/p\u003e\u003cp\u003eHow to Apply Gluvit Epoxy Sealer\u003c\/p\u003e\u003cp\u003eDeteriorated wood can be renewed with a few strokes of Gluvit. It penetrates and strengthens stringers, decking and molding. Gluvit’s excellent impact and abrasion resistant barrier coat minimizes fiberglass blistering and corrosion. Seals leaky aluminum seams, rivets, and leaks around cabins or decks.\u003c\/p\u003e\u003cp\u003eRemove contaminants* such as grease, oil, dirt with lacquer thinner or strong detergent. Sand to bare surface with 80-100 grit sand paper to ensure adhesion. Remove all grit and dust after sanding with another rinse of solvent. *When cleaning aluminum surfaces an Aluminum Prep Wash can aid in scarifying the surface.\u003c\/p\u003e\u003cp\u003eFill deep holes (more than 1\/8\" in depth) with Marine-Tex Epoxy Putty before applying Gluvit.\u003c\/p\u003e\u003cp\u003ePre-proportion sufficient resins and hardener in the correct ratio to cover the areas to be sealed and\/or repaired. Gluvit can be broken up into separate batches if desired. Mix ratio by volume for batches is 5 parts resin to 1 part hardener. If you will be using the entire kit at once, add the entire contents of the hardener into the resin and thoroughly mix contents for 3-4 minutes to insure complete mixing. Be sure you can use the entire kit within the pot life or working time period.\u003c\/p\u003e\u003cp\u003eApply Gluvit with a brush or roller at 6-8 mils film thickness. Lightly drag a foam brush in long even strokes over the freshly applied coating to smooth the surface. After the first coat cures for 12 hours at 72°F, a second coat can be applied for optimum performance.\u003c\/p\u003e\u003cp\u003eGluvit hardens overnight. Allow 48 hours at 72°F for maximum strength. Working time and cure will be longer at lower temperatures, shorter at higher temperatures. Note: If ambient temperature is below 50°F, pre-condition Gluvit and work area to at least 55°F.\u003c\/p\u003e\u003cp\u003eApplication Information:\u003c\/p\u003e\u003cp\u003eGluvit offers an open time of about 60 minutes at 72°F to provide adequate working time for larger jobs, such as an entire deck or hull.\u003c\/p\u003e\u003cp\u003eGluvit cures in 24-30 hours at 72°F. Apply heat to speed cure if necessary or if the temperature will be below 55°F.\u003c\/p\u003e\u003cp\u003eGluvit may be applied over mildly damp (not wet) surfaces. Do not apply Gluvit when rain is pending.\u003c\/p\u003e\u003cp\u003eIn the uncured state, Gluvit will absorb rain water, turn milky white, and take longer to cure - but it will harden in time.\u003c\/p\u003e\u003cp\u003eTo overcoat Gluvit after cure, wash the surface with warm soapy water or a dilute vinegar solution and a fine abrasive pad, or wet sand, then dry with clean towels or cloth. Frost-sand surface with 80-100 grit sand paper to remove any gloss. Gluvit can be overcoated with any marine paint or other coating …\u003c\/p\u003e","brand":"ITW Marine Tex","offers":[{"title":"Default Title","offer_id":50581726527746,"sku":"ITW-RM330K","price":100.29,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0842\/3024\/2562\/files\/itw-rm330k_lg__04141.1558180257_3f8fdaeb-fbcb-4297-8373-7a6854aa8b16.jpg?v=1791078481","url":"https:\/\/allmarineworld.com\/products\/gluvit-epoxy-waterproof-sealer","provider":"All Marine World","version":"1.0","type":"link"}