{"product_id":"garelick-compact-eez-in-ii-transom-ladder","title":"Garelick Compact Ii 3 Step Ladder","description":"\u003cp\u003eGarelick Compact EEz-In II Transom Ladder\u003c\/p\u003e\u003cp\u003eFeatures:\u003c\/p\u003e\u003cp\u003eCompact EEz-In II Transom Ladder\u003c\/p\u003e\u003cp\u003eHelps provide Unassisted Re- boarding\u003c\/p\u003e\u003cp\u003eInvisible, Quick \u0026amp; Easy and Readily Accessible\u003c\/p\u003e\u003cp\u003eComplete ladder stows within transom and hull\u003c\/p\u003e\u003cp\u003e3 steps open \u0026amp; close independently for ease of boarding\u003c\/p\u003e\u003cp\u003eQuick release ring w\/ self-locking latch deploys ladder from storage\u003c\/p\u003e\u003cp\u003eAnodized aluminum channel body deploys out at 15 degree angle\u003c\/p\u003e\u003cp\u003eDimensions:\u003c\/p\u003e\u003cp\u003e3 Step Compact Ladder - 32.5\" (83 cm) length\u003c\/p\u003e\u003cp\u003e2\" (5cm) square channel body\u003c\/p\u003e\u003cp\u003etransom mount plate 5\"H x 4.5\"W x 1\" D (13 x 11 x 3 cm)\u003c\/p\u003e\u003cp\u003eMounting Instructions\u003c\/p\u003e\u003cp\u003eHOW TO MOUNT GARELICK COMPACT EEZ-IN II TRANSOM LADDER\u003c\/p\u003e\u003cp\u003eMounting Instructions\u003c\/p\u003e\u003cp\u003eChoose the most suitable side of your transom for mounting the ladder. Locate a flat surface (4 ½” wide x 5” high) where the ladder will not interfere with the turning of the motor or be excessively close to the propeller of your boat.\u003c\/p\u003e\u003cp\u003eMake sure that the location will be a minimum of 4” ABOVE the waterline at the bottom of the faceplate\/assembly and in an area where there are NO electrical wires, hydraulic hoses, water hoses or steering cables.\u003c\/p\u003e\u003cp\u003eCheck to see that the transom area is sufficiently strong enough to support the ladder while it is in use. If necessary, a backing plate may need to be installed to reinforce the area.\u003c\/p\u003e\u003cp\u003eDrill a 3” diameter hole in the transom, making sure it is parallel to the waterline.\u003c\/p\u003e\u003cp\u003ePlace the ladder assembly into the hole and mark the four faceplate mounting hole’s locations.\u003c\/p\u003e\u003cp\u003eDrill the holes for appropriate 5\/16” diameter hardware (not included).\u003c\/p\u003e\u003cp\u003eNOTE: It is preferred to through-bolt the assembly for a secure installation (use locknuts and backing washers)\u003c\/p\u003e\u003cp\u003eCaulk the entire area to be mounted and insert the ladder. Secure in place with the selected mounting hardware.\u003c\/p\u003e\u003cp\u003eSecure the far end of the ladder to the boat with a strap or some other means to keep the ladder tube in place (not provided as all installations may vary).\u003c\/p\u003e\u003cp\u003eMaintenance:\u003c\/p\u003e\u003cp\u003eRegular fresh water rinsing and periodic cleaning with a mild abrasive cleaner will help retain lustre and help reduce corrosion.\u003c\/p\u003e\u003cp\u003ePeriodically check mounting hardware and re-tighten (due to normal boat operation).\u003c\/p\u003e\u003cp\u003eSafety:\u003c\/p\u003e\u003cp\u003eNever operate your boat with the ladder in “down” position. Serious injury or damage to your boat or ladder may result.\u003c\/p\u003e\u003cp\u003eInformation sourced from the Garelick 19700 Series Invisible Ladder\u003c\/p\u003e\u003cp\u003eInstallation Instructions\u003c\/p\u003e\u003cp\u003eFrequently Asked Questions\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eWhat is the Garelick Compact EEz-In II Transom Ladder used for? The Garelick Compact EEz-In II Transom Ladder is designed to provide unassisted re-boarding from the water. Its three steps open and close independently, while the complete ladder stores within the transom and hull for quick access when boarding is needed.\u003c\/li\u003e\n\u003cli\u003eHow does the Garelick Compact EEz-In II Transom Ladder deploy? A quick-release ring with a self-locking latch deploys the ladder from its stored position. The anodized aluminum channel body extends outward at a 15-degree angle, providing access to the three-step ladder for re-boarding.\u003c\/li\u003e\n\u003cli\u003eWhat are the dimensions of the Garelick Compact EEz-In II Transom Ladder? The three-step Compact EEz-In II ladder is 32.5 inches (83 cm) long and uses a 2-inch (5 cm) square channel body. The transom mount plate measures 5 inches high by 4.5 inches wide by 1 inch deep.\u003c\/li\u003e\n\u003cli\u003eWhat should I check before mounting the Garelick Compact EEz-In II Transom Ladder? Choose a flat transom surface measuring at least 4.5 inches wide by 5 inches high, with the bottom of the faceplate at least 4 inches above the waterline. Make sure the ladder will not interfere with motor turning or be excessively close to the propeller, and verify that the area contains no electrical wires, hydraulic hoses, water hoses, or steering cables.\u003c\/li\u003e\n\u003cli\u003eWhat mounting hardware is required for the Garelick Compact EEz-In II Transom Ladder? The mounting instructions call for holes sized for approp…\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Garelick","offers":[{"title":"Default Title","offer_id":50581673246978,"sku":"GAR-19700","price":384.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0842\/3024\/2562\/files\/gar-19700_lg__19057.1558176177.jpg?v=1791078153","url":"https:\/\/allmarineworld.com\/products\/garelick-compact-eez-in-ii-transom-ladder","provider":"All Marine World","version":"1.0","type":"link"}